HMC Electronics ASG-SD2500-10FX-SY X-PAQ Precision Fastening System - Manual (Page 21)

If a task is being selected through the inputs by an external signal, the task button will not allow
a user to manually select a task, the external input will have to be removed to free the logic and
allow the manual selection.
• ENABLE BOLTS: From the ‘Run Tool’ Screen:
o Tap the ‘Setup’ Button
o Make sure the task shown at the top is the one to be programmed.
o Tap the ‘Inputs’ Button
Assuming that there is only 1 bolt in your sequence, tap the button on the l
You should now see a column of buttons appear in the chart next to each input number. You
may now select which input you want to use to enable the bolt by tapping the ‘Ignore’ button to
the right of that input. This will toggle b
to the right of this button shows what the
yellow [<<] button at the top and save changes if desired.
Note: If you have multiple bolts in
you set that up in the ‘Setup’ and ‘Bolt Sequences’ screens prior to completing this step. You
will then want to make sure you set up each bolt you wish to be enabled with the input. For
your convenience, with multiple bolts a
you to select all bolts and set them up simultaneously.
• REMOTE START: From the ‘Run Tool’ Screen:
o Tap the ‘Setup’ Button
o Make sure the task shown at the top is the one to be
o Select the ‘Remote Start’ radio button in the ‘Triggering’ section.
o Tap the ‘Inputs’ Button
o Tap the arrow button on the
Select the ‘Remote Start’ button on the left side of the scre
buttons appear in the chart next to each input number. You may now select which input you
Highlight
Page 21
If a task is being selected through the inputs by an external signal, the task button will not allow
a user to manually select a task, the external input will have to be removed to free the logic and
w the manual selection.
: From the ‘Run Tool’ Screen:
Tap the ‘Setup’ Button
Make sure the task shown at the top is the one to be programmed.
Tap the ‘Inputs’ Button
Assuming that there is only 1 bolt in your sequence, tap the button on the left that says ‘Bolt 1’.
You should now see a column of buttons appear in the chart next to each input number. You
may now select which input you want to use to enable the bolt by tapping the ‘Ignore’ button to
the right of that input. This will toggle between ‘H’,’L’, and ‘Ignore’ with each tap. The picture
to the right of this button shows what the controller is currently seeing on that input. Press the
button at the top and save changes if desired.
: If you have multiple bolts in your application sequence, it is recommended that
you set that up in the ‘Setup’ and ‘Bolt Sequences’ screens prior to completing this step. You
will then want to make sure you set up each bolt you wish to be enabled with the input. For
, with multiple bolts an ‘All’ button will appear on the ‘Input’ screen to allow
you to select all bolts and set them up simultaneously.
: From the ‘Run Tool’ Screen:
Tap the ‘Setup’ Button
Make sure the task shown at the top is the one to be programmed.
Select the ‘Remote Start’ radio button in the ‘Triggering’ section.
Tap the ‘Inputs’ Button
Tap the arrow button on the bottom next to ‘Setup Bolt(s)’ so that ‘Setup Misc’ appears.
Select the ‘Remote Start’ button on the left side of the screen. You should now see a column of
buttons appear in the chart next to each input number. You may now select which input you
If a task is being selected through the inputs by an external signal, the task button will not allow
a user to manually select a task, the external input will have to be removed to free the logic and
eft that says ‘Bolt 1’.
You should now see a column of buttons appear in the chart next to each input number. You
may now select which input you want to use to enable the bolt by tapping the ‘Ignore’ button to
etween ‘H’,’L’, and ‘Ignore’ with each tap. The picture
is currently seeing on that input. Press the
sequence, it is recommended that
you set that up in the ‘Setup’ and ‘Bolt Sequences’ screens prior to completing this step. You
will then want to make sure you set up each bolt you wish to be enabled with the input. For
‘All’ button will appear on the ‘Input’ screen to allow
so that ‘Setup Misc’ appears.
en. You should now see a column of
buttons appear in the chart next to each input number. You may now select which input you
Documentation Provided By HMC Electronics
33 Springdale Ave. Canton, MA 02021
http://www.hmcelectronics.com
(800) 482-4440