Det-Tronics X3301 Multispectrum IR Flame Detector - Manual (Page 21)

19 95-8527 19.2
REPlaCEmENT PaRTS
The detector is not designed to be repaired in the field.
If a problem should develop, refer to the Troubleshooting
section. If it is determined that the problem is caused by
an electronic defect, the device must be returned to the
factory for repair.
REpLACEMENT pARTs
part Number Description
009208-001
oi Replacement kit for X3301 (5 Black Reflector Plates)
with Inspector Connector and Monitor
010831-001
oi Replacement kit for X3301 (5 Stainless Steel Reflector Plates)
with Inspector Connector and Monitor
007307-001
Replacement oi Reflector Plates for X3301 with Black plate
(requires Inspector Connector to calibrate)
010830-001
Replacement oi Reflector Plates for X3301 with Stainless Steel
plate (requires Inspector Connector to calibrate)
NOTE : Refer to instruction manual 95-8530 to determine the correct oi Replacement Plate.
DEVICE REPaIR aND RETURN
Prior to returning devices, contact the nearest local
Detector Electronics office so that a Return Material
Identification (RMI) number can be assigned. A
written statement describing the malfunction must
accompany the returned device or component to
assist and expedite finding the root cause of the
failure.
Pack the unit properly. Always use sufficient packing
material. Where applicable, use an antistatic bag as
protection from electrostatic discharge.
NOTE
Det-Tronics reserves the right to apply a service
charge for repairing returned product damaged as
a result of improper packaging.
Return all equipment transportation prepaid to the factory
in Minneapolis.
NOTE
It is highly recommended that a complete spare
be kept on hand for field replacement to ensure
continuous protection.
ORDERING INfORmaTION
When ordering, please specify:
X3301 Multispectrum IR Flame Detector
Refer to the X3301 Model Matrix for details
Q9033 Mounting Arm is required:
– Q9033A for aluminum detectors only
– Q9033B for aluminum and stainless steel detectors
ACCEssORIEs
part Number Description
000511-029 Converter RS485 to RS232
103881-001 Converter RS485 to USB
007819-001
W6300B1002 Serial Inspector Connector
(Inspector Monitor software included)
007819-002
W6300B1003 USB Inspector Connector
(Inspector Monitor software included)
009207-001 Flame Inspector Monitor CD
103922-001 Model 475 HART Communicator
102740-002 Magnet
008082-001 Magnet and Adapter for Extension Pole
007739-001 Magnet and Extension Pole
007240-001 Q1116A1001, Air Shield (AL)
007818-001 Q1118A1001 Aluminum Air Shield/Flange Mount (AL)
007818-002 Q1118S1001 Stainless Steel Air Shield/Flange Mount (SS)
009177-001 Q1120A1001 Paint Shield mounting ring (AL)
010857-001 Q1130A1001 Flange Mount Assembly
006097-001 Q1201 Laser
102871-001 Laser Battery, 3V Lithium (laser)
007255-001 Q1201C1001 X-Series Laser Holder (AL/Plastic)
007338-001 Q2000A1001 X-Series Weather Shield (AL)
007338-010 Q2033A10R X3301/X3302 FOV Limiter 10° (AL)
007338-020 Q2033A20R X3301/X3302 FOV Limiter 20° (AL)
007338-030 Q2033A30R X3301/X3302 FOV Limiter 30° (AL)
007912-010 Spare Restrictor Plate 10° (AL)
007912-020 Spare Restrictor Plate 20° (AL)
007912-030 Spare Restrictor Plate 30° (AL)
007290-001
Q9033B Stainless Steel Mounting Arm Assembly is for
aluminum and stainless steel detectors
007290-002
Q9033A Aluminum Mounting Arm Assembly is for aluminum
detectors only
011385-001 Q9033 Collar Attachment
101197-001 Stop Plug, 3/4” NPT, AL
101197-004 Stop Plug, 3/4” NPT, SS
101197-005 Stop Plug, M25, AL, IP66
101197-003 Stop Plug, M25, SS, IP66
010816-001 Stop Plug, 20 Pack, 3/4”NPT, AL
010817-001 Stop Plug, 20 Pack, 3/4”NPT, SS
010818-001 Stop Plug, 20 Pack, M25, AL, IP66
010819-001 Stop Plug, 20 Pack, M25, SS, IP66
103363-001 14 mm Hex Wrench (Steel)
103406-001 Screwdriver
107427-040 O-ring - Rear Cover (Viton)
005003-001 1 oz grease for detectors (non-silicon)
001680-001 Window cleaner (6 pack)