Advance Adapters 716131-E User Manual
Advance adapters inc

ADVANCE ADAPTERS INC.
P/N: 716131-A
P.O. Box 247, 4320 Aerotech Center Way
P/N: 716131-B
Paso Robles, CA 93447
P/N: 716131-E
Telephone: (800) 350-2223
Fax: (805) 238-4201
Page Rev. Date:
06-19-09
KIT NO.
716131-A / B / and E
CONSISTS OF:
No.
Qty.
Part No.
Description
1.
1
712548-PLT
DUST COVER PLATE
2.
1
716131
ADAPTER PLATE
3.
2
716131-DP
SPECIAL DOWEL PINS FOR AMC TRANS TO ADAPTER
4.
1
716131-TR
TORQUE CONVERTER ADAPTER RING
5.
4
720060
8MM-1.0 X 25MM HHCS
6.
4
723136
5/16-24 X 1" HHCS
7.
2
723701
3/8" HEX NUT
8.
17
723704
3/8" LOCK WASHER
9.
2
723714
STUD BOLT 3/8"-16 x 1-1/2"
10.
2
723720
H.H.C.S. 3/8"-16 x 3/4" LONG0
11.
4
723722
HEX HEAD BOLT 3/8"-16 x 1-1/4" LONG
12.
2
723730
SOCKET HEAD CAP SCREW 3/8"-16 x 1-1/4" LONG
13.
4
723735
FLAT WASHER FOR TORQUE CONVERTER BOLTS
14.
5
723744
HEX HEAD CAP SCREW 3/8"-16 x 2-1/4"
15.
6
723758
HEX HEAD CAP SCREW 3/8"-16 x 3/4"(FLEXPLATE BOLTS)
16.
4
723760
3/8-24 X 1" HHCS
17.
1
JP001
JEEP INSTRUCTION MANUAL
JEEP 727 & 999 TORQUEFLITE TO CHEVY
ENGINES (REPLACING AMC 6 CYL.)
Torqueflite 999
JEEP 727 & 999 TORQUEFLITE:
This adapter plate is designed for exclusive use on AMC Torqueflite transmissions manufactured from 1980 & up. The
transmission being used must have been previously installed with a 6 cylinder engine. Vehicles that were previously
equipped with a 4 cylinder engine or 2.8 V6 will not be able to use this adapter. Jeep used some 727 transmissions
between 1973 through 1979. This kit is not compatible with these transmissions.
IN ORDER TO AVOID TRANSMISSION DAMAGE, THE CUSTOMER MUST VERIFY THE CORRECT CON-
VERTER LOCATION.
The difference between the 727 and the 999 transmissions is in the size of the bolts that hold the converter to the
flexplate.
We have provided 3/8"-24 NF bolts for the 999 transmissions 1980-1991, 5/16"-24 NF for the 727
transmission, and 8mm x 20mm socket head bolts for 1992 & newer 999 transmissions. These bolts must be used with
flat washers and thread retainer.
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
INSTALLATION PROCEDURES
1. The torque converter must first be installed into the transmission assembly. Make sure the notches on the converter
line up with the drive notches in the transmission. Install the converter to the maximum depth or position inside
transmission. The torque converter must be
installed onto the transmission making sure
that both sets of splines are properly engaged.
We recommend that you take a measurement
of the stock AMC flexplate in reference to the
stock AMC block
(see photos)
. This measure-
ment should be approximately 1/2".
The photos
(right)
show the stock AMC engine
and stock flexplate. The measurement is
taken from the transmission side of the flex-
plate to the back of the engine block. Our adapter kit will make the GM block look basically the same as the this
AMC setup. It will also give you approximately the same measurement.
This adapter kit previous to this
rev. date of 5-14-09 used a steel
ring and a converter bushing. This
new style kit is interchangeable
with the earlier style adapter kits.
The converter bushing and steel
ring are replaced with the new
aluminum ring.