AEM 30-3520 Infinity Plug & Play Harnesses - Nissan/Infiniti 2003-2006 350Z/G35 - Manual (Page 32)

32
© 2014 AEM Performance Electronics
P/N 30-3520
Infinity
Pin
Hardware Reference
2003–2006 350Z/
G35
Specification
Dest. Pin
350Z/
G35
Hardware Specification Notes
C1-72 Harness_Stepper_1B Stepper 1B
Programmable Stepper
Driv er, up to 28V and
±1.4A
Be sure that each internal coil of the
stepper motor is properly paired with
the 1A/1B and 2A/2B ECU outputs.
Supports Bi-Polar stepper motors only .
C1-73 Power Ground Ground 115 Power Ground Connect directly to battery ground.
C2-1 Harness_HBridge1_0 Not used
5.0A max Throttle Control
Hbridge
Not used
C2-2 Harness_HBridge1_1 Not used
5.0A max Throttle Control
Hbridge
Not used
C2-3 Power Ground Ground 116 Power Ground Connect directly to battery ground.
C2-4 Harness_Injector_6 Injector 7
Saturated or peak and
hold, 3A max continuous
Injector 7
C2-5 Harness_Injector_7 Injector 8
Saturated or peak and
hold, 3A max continuous
Injector 8
C2-6 Harness_Injector_8 Injector 9
Saturated or peak and
hold, 3A max continuous NOTE: Only av ailable with Inf inity 10
Nissan
C2-7 Harness_Injector_9 Injector 10
Saturated or peak and
hold, 3A max continuous NOTE: Only av ailable with Inf inity 10
Nissan
C2-8 Power Ground Ground 116 Power Ground Connect directly to battery ground
C2-9 +12V +12V In 3 12 v olt power f rom relay
12 v olt power f rom relay . Relay must
be controlled by +12V Relay Control
signal, pin C1-29 abov e.
C2-10 Harness_Injector_10 Injector 11
Saturated or peak and
hold, 3A max continuous NOTE: Only av ailable with Inf inity 10
Nissan
C2-11 Harness_Injector_11 Injector 12
Saturated or peak and
hold, 3A max continuous NOTE: Only av ailable with Inf inity 10
Nissan
C2-12 Harness_Analog_In_17
A/C Analog
Request
12 bit A/D, 100K pullup to
5V
0–5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low ref erence. Do not
connect signals ref erenced to +12V as
this can permanently damage the
ECU. See Setup Wizard Input
Functions page f or input selection.
See AC_Request_In 1-axis table f or
activ ation logic.
C2-13 Harness_Analog_In_18
Acceleration
Pedal Position 1
106
12 bit A/D, 100K pullup to
5V
0–5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low ref erence. Do not
connect signals ref erenced to +12V as
this can permanently damage the
ECU. See the Driv e by Wire Wizard
f or calibration.
C2-14 Harness_Analog_In_19
Acceleration
Pedal Position 2
98
12 bit A/D, 100K pullup to
5V
0–5V analog signal. Use +5V Out pins
as power supply and Sensor Ground
pins as the low ref erence. Do not
connect signals ref erenced to +12V as
this can permanently damage the
ECU. See the Driv e by Wire Wizard
f or calibration.