Neff B45C52N3GB - Manual (Page 9)

9
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness “hard“ (
™…„ ) is the default setting. Change
the setting if the water is softer.
You can determine the water hardness with the test strips
supplied or ask your water supplier.
Notes
■
If your water is very hard, we recommend that you use
softened water.
■
If you use only softened water, you can, in this case, set your
appliance to the softened water hardness range.
■
If you use mineral water, then set the water hardness range to
hard.
■
If you use mineral water, then it must be non-carbonated (see
chapter: Filling and emptying the water tank).
1. Use the temperature selector to set the water hardness
range.
2. Press and hold the ± info button for 3 seconds.
Your setting is saved. ™†‚ appears in the temperature
display.
Calibrating the altitude
The altitude difference range “0 - 300 m“ ( ™†‚ ) is the default
setting. Change this setting if the location of the appliance is
higher or lower than this.
1. Use the temperature selector to set the altitude difference
range.
2. Press and hold the ± info button for 3 seconds.
Your setting is saved.
Setting the clock
Note: When you press the KJ clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹ : ‹‹ flashes in the clock display.
1. Briefly press the KJ clock function button to go to the
setting mode.
The
KJ and 3 symbols light up. ‚ƒ : ‹‹ appears in the
clock display.
2. Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the KJ clock function
button repeatedly until the KJ and 3 symbols light up again.
Change the time with the rotary selector.
Cleaning the appliance
Clean your appliance before using it for the first time.
1. Remove the accessories from the cooking compartment.
2. Completely remove any residual packaging (e.g. bits of
polystyrene) from the cooking compartment.
3. Clean the accessories and cooking compartment with hot
soapy water (see chapter: Cleaning and care).
4. Fill water tank with 400 ml water (see chapter: Filling and
emptying the water tank).
5. Slide in the water tank all the way.
6. Using the operating mode selector set % Top/bottom
heating (see chapter: Operating the appliance).
7. Use the temperature selector to set the temperature to
240 °C.
8. Press the Ÿ AquaAssist button repeatedly until the • ž Ÿ
symbols light up (see chapter: AquaAssist - steam-assisted
cooking).
9. Press the ƒ start button.
10. Switch off the appliance if the water tank is empty. To do
this, turn the operating mode selector back to the off position
Û and retract it.
The remaining water will be pumped out of the evaporator
system. The Ì symbol lights up.
11. Emptying the water tank (see chapter: Filling and emptying
the water tank)
12. Afterwards, wipe the cooled cooking compartment with hot,
soapy water.
Note: Remove limescale with a cloth soaked in vinegar, then
wipe with clean water and rub dry with a soft cloth.
13. Clean the outside of the appliance with a soft, damp cloth
and soapy water.
Water hardness range Setting symbol (temperature dis-
play)
softened ™…‹
soft ™…‚
medium ™…ƒ
hard ™…„
Altitude difference
range
Setting symbol (temperature dis-
play)
Under 0 m ™†‹
0 - 300 m ™†‚
300 - 600 m ™†ƒ
600 - 900 m ™†„
900 - 1200 m ™†…
1200 - 1500 m ™††
1500 - 1800 m ™†‡
1800 - 2100 m ™†ˆ
2100 - 2400 m ™†‰
above 2400 m ™†Š