Speaker setting – Pioneer SC-LX78-S User Manual
Page 104
104
The System Setup and Other Setup menus
12
! 5.2 +ZONE 2+HDZONE – Select to use the surround back (ZONE 2) and front wide (HDZONE) speaker termi-
nals for an independent systems in another zone (see
on
! 5.2ch + SP-B Bi-Amp – Select this setting if you’re bi-amping your B speakers (see
).
! 5.2ch F+Surr Bi-Amp – Select this setting if you’re bi-amping your front and surround speakers (see
on
! 5.2ch F+C Bi-Amp – Select this setting if you’re bi-amping your front and center speakers (see
on
! 5.2ch C+Surr Bi-Amp – Select this setting if you’re bi-amping your center and surround speakers (see
on
! Multi-ZONE Music – See
3 If you selected 7.2.2ch TMd/FW, 7.2.2ch TMd/FH, 7.2ch + Speaker B, 7.2ch + Front Bi-Amp,
or 7.2ch + HDZONE in Step 2, select the placement of the surround speakers.
In a 7.2-channel surround system with surround speakers placed directly at the sides of the listening position, the
surround sound of 5.1-channel sources is heard from the side. This function mixes the sound of the surround speak-
ers with the surround back speakers so that the surround sound is heard from diagonally to the rear as it should be.
Depending on the positions of the speakers and the sound source, in some cases it may not be possible to
achieve good results. In this case, set the setting to ON SIDE or IN REAR.
! ON SIDE – Select when the surround speakers is positioned right beside you.
! IN REAR – Select when the surround speaker is positioned obliquely behind you.
4 When ‘Setting Change?’ is displayed, select Yes.
If No is selected, the setting is not changed.
You will return to the Manual SP Setup menu.
Using Multi-ZONE Music
Multi-ZONE Music can be used to play the same sound in the MAIN ZONE, ZONE 2 and ZONE 3, for example for
home parties. Normally set Speaker System to 5.2 +ZONE 2+ZONE 3 for multi-zone/multi-source playback, then
switch it to Multi-ZONE Music when having a home party. When this is done, the sound of the input function
selected for the MAIN ZONE is played in all zones (the MAIN ZONE, ZONE 2 and ZONE 3).
! There is virtually no delay in the sound.
! Switching of the input for only ZONE 2 or ZONE 3 is disabled, but the volume can be adjusted or muted for the
individual zones.
! This is only valid for ZONE 2 and ZONE 3 connections using the speaker terminals. No sound is output from the
ZONE 2 and ZONE 3 pre-out terminals. Nothing is output from the ZONE 2 and ZONE 3 COMPONENT VIDEO
output and VIDEO output terminals.
! The HDZONE setting does not apply to Multi-ZONE Music.
Speaker Setting
Use this setting to specify your speaker configuration (size, number of speakers and crossover frequency). It is a good
idea to make sure that the settings made in
Automatically conducting optimum sound tuning (Full Auto MCACC)
are correct. Note that this setting applies to all MCACC presets, and cannot be set independently.
1 Select ‘Speaker Setting’ from the Manual SP Setup menu.
2 Choose the set of speakers that you want to set, then select a speaker size.
Use
k/l to select the size (and number) of each of the following speakers:
! Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to the subwoofer.
! Center – Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect a center speaker, choose NO
(the center channel is sent to the front speakers).
! TMd – Select LARGE if your top middle speakers reproduce bass frequencies effectively, or select SMALL
to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select
Dolby Sp (
). If you didn’t connect the top middle speakers, choose NO (the top middle channel is
sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2.2ch TMd/FW, 7.2.2ch TMd/FH,
5.2.4ch or 7.2ch + Speaker B.
— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance
may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is
bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of
Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and
LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.
! TFw – Select LARGE if your top forward speakers reproduce bass frequencies effectively, or select SMALL
to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select
Dolby Sp (
). If you didn’t connect the top forward speakers, choose NO (the top forward channel is
sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 5.2.4ch.
— When you set
TBw to NO, this setting is automatically set to NO.
— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance
may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is
bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of
Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and
LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.
! TBw – Select LARGE if your top backward speakers reproduce bass frequencies effectively, or select SMALL
to send bass frequencies to the other speakers or subwoofer. When Dolby Enabled Speaker is used, select
Dolby Sp (
). If you didn’t connect the top backward speakers, choose NO (the top backward chan-
nel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 5.2.4ch.
— When you set TFw to NO, this setting is automatically set to NO.
— If you change the setting from Dolby Sp to SMALL or LARGE, the set value for Speaker Distance
may be changed. This is because the maximum value of Speaker Distance when set to Dolby Sp is
bigger than the maximum value of Speaker Distance when set to SMALL and LARGE. If the value of
Speaker Distance set to Dolby Sp exceeds the maximum value of Speaker Distance for SMALL and
LARGE, Speaker Distance for SMALL and LARGE is set to its maximum value.
! FH – Select LARGE if your front height speakers reproduce bass frequencies effectively, or select SMALL to
send bass frequencies to the other speakers or subwoofer. If you didn’t connect front height speakers, choose
NO (the front height channel is sent to the front speakers).
— You can adjust this setting only when Speaker System setting is 7.2.2ch TMd/FH.
— If the surround speakers are set to
NO, this setting will automatically be set to NO.