Vaddio HE120 Operating Instructions - Manual (Page 36)

36
Parts and their functions
(continued)
 LAN connector for IP control [LAN ACT/LINK]
This LAN connector (RJ45) is connected when exercising
IP control over the unit from an external device.
Use a cable with the following specifications for the
connection to the LAN connector:
When connecting through a hub:
LAN cable* (category 5 or above, straight cable),
max. 100 meters [328 ft]
When a hub is not used:
LAN cable* (category 5 or above, crossover cable),
max. 100 meters [328 ft]
*: Use of an STP (shielded twisted pair) cable is
recommended.
 HDMI connector [HDMI]
This is the HDMI video output connector.
 Anti-theft wire mounting hole
The anti-theft wire bracket (available from a hardware
store) is attached here.
 Service switch [SERVICE]
This switch is used for maintenance purposes: Do not
touch it.
If it is pressed by mistake, the service screen will be
displayed. If this happens, turn off the power and then turn
it back on.
 G/L IN connector [G/L IN]
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the
video signal format which has been set.
Format
External sync signal input format
BBS Tri-level sync
1080/59.94p(i)
1080/59.94i
720/59.94p
480/59.94p(i)
480/59.94i 480/59.94i
480/59.94i
—
480/59.94i
480/59.94i 1080/59.94i
1080/59.94i
720/59.94p
—
—
1080/50p(i)
1080/50i
720/50p
576/50p(i)
576/50i 576/50i
576/50i
—
576/50i
576/50i 1080/50i
1080/50i
720/50p
—
—
 VIDEO OUT connector [VIDEO OUT]
This is the output connector used for monitoring the
camera’s composite video signals. Use the monitor in the
internal synchronization mode.
Provide a BNC coaxial cable as the connecting cable.
With the HD format, the signals are output with a 90H
delay from the HD signals.
 Hole used to secure cable cover
Use the screw provided to secure the cable cover.
 SDI OUT connector [HD/SD SDI OUT]
This is the SDI video signal output connector.
 HD/SD analog output connector
[HD/SD ANALOG OUT]
This is the output connector of the camera’s HD/SD
component video signals.
Provide a D-Sub 15-pin connecting cable (VGA cable)
or D-Sub 15-pin and BNC coaxial connector conversion
cable as the connecting table.
Use a high-quality cable.
Pin No. Signal name Pin No. Signal name
1 R/Pr 9 GND
2 G/Y 10 GND
3 B/Pb 11 GND
4 GND 12 GND
5 GND 13 —
6 GND 14 —
7 GND 15 GND
8 GND
 DC IN connector [12V IN ]
Connect the AC adaptor supplied with the unit to this
connector to supply the DC 12 V voltage to the unit.
 Cable clamp
This is used to hold the cable connection to the DC IN
connector and prevent it from becoming disconnected.
 IR ID switches [IR ID]
[CAM1] [CAM2] [CAM3] [CAM4]
These are used to select the ID of the wireless remote
control (optional accessory).
The IR ID switch settings “CAM1” to “CAM4” correspond
to the [CAM1] to [CAM4] buttons on the wireless remote
control.
 Square holes (  2) for cable cover tabs
The tabs on the two sides of the cable cover are fitted into
these holes.
 Threaded hole (thread: 1/4-20UNC, ISO1222
[6.35 mm]) for mounting the camera
Use this hole when mounting the camera on a tripod, etc.