Aiphone JK-DVF-AC User Manual

Page 10

English

Français

Nederlands

· When the relay 1 output time is

set to latched output, the
auto-relock function is
disabled.

· When the auto-relock function

is turned on, the unlock
function of the request to
exit/entry button of relay 2 is
disabled.

· If the 0 key illumination function

is turned on while the timer is
on, only the 0 key illumination
will light up, even if the "key
illumination time setting" is set
to "Indicator is continually lit".

OFF

Operation

tone OFF

Operation

tone ON

Operation

tone OFF

Operation

tone ON

Relays 1 and 2

are both linked

Relays 1 and 2

are both linked

Only relay 1

is linked

Input the setting code.

Lockout

(Default: OFF)

Auto-relock

(Anti-tailgate)

(Default: OFF)

Timer-linked unlocking setting

(Default: relay 1, OFF)

Operation sound settings

(Default: ON)

0 key illumination ON

while timer is on

0 key illumination OFF

while timer is on

0 key illumination ON

while timer is on

0 key illumination OFF

while timer is on

Inputting the number of operations

(ex.：10 times)

10 -99

Inputting length of time in "Lockout" mode

(Ex.: 10 seconds)

10 - 99

Input the master code twice.
(Default : )

Only relay 1

is linked

Only relay 2

is linked

Only relay 2

is linked

Beep

(orange)

Illumination

(green)

Blinking

Bleep, Bleep

Illumination Blinking

Bleep

Illumination Blinking

Bleep

Beep

Illumination Blinking Illumination Blinking

Bleep

Illumination Blinking

Bleep

Illumination Blinking

Beep

Illumination Blinking

Beep

- When the key is pressed, the green LED lights up, the buzzer beeps twice, and the system exits the setting mode.

(If the key is included in the user code and the master code, the system does not exit the setting mode.)

- You can continue the setting up operation by entering an arbitrary setting code.

Indicator

goes out Blinking

Bleep,

Bleep

External output setting

(Default: OFF)

Input the setting code.

Illumination

Blinks three times

Blinking

OFF

During lockout

and forced

entry output

During

Lockout

During forced

entry output

During lockout

and forced

entry output

Input the setting code.

Reset Settings

Illumination Blinking

(orange)

Illumination

(green)

Blinking

Input the master code twice.
(Default : )

During

Lockout

During forced

entry output

Bleep, Bleep, Beep

Beep

Bleep, Bleep

Bleep

Inputting of relay output time

(ex.: 99 seconds)

01 - 99

Latched (※) : 00

When setting relay 1

When setting relay 2

Setting the relay output time

(Default: 3 Sec.)

Input the setting code. Input the setting code.

Illumination Blinking

Beep

Bleep

Setting the key illumination time

(Default: 10 Sec.)

Input the setting code.

Inputting of illumination time

(ex.: 20 seconds)

10 - 99

Indicator is lit up at all times: 00

Illumination Blinking

Beep

Bleep

When the key is pressed, the green LED lights up, the buzzer beeps twice, and the system exits the setting mode.

(If the key is included in the user code and the master code, the system does not exit the setting mode.)

- You can continue the setting up operation by entering an arbitrary setting code.

Indicator

goes out Blinking

Bleep,

Bleep

· If the power is turned off and

the , , and keys are
pressed simultaneously while the
unlock 1 input status is active
(short circuit between terminals
PB1 and C), the settings can be
returned to their default values by
turning the power back on and
pressing the , , and
keys simultaneously for 3
seconds.

· When setting the external output,

do not set the relay 2 output to be
latched.

· (※) If the latched status has

been set and the door is
unlocked, it will not be locked
again until the user code is
entered (or the request to
exit/entry button is pressed, or
the key is pressed while
timer-linked unlocking is set).

· When the door is unlocked

during relay outputting
(including when latched), the
system cannot be switched to
the setting mode.

JK-DVF-AC_ENG.indd 9

2009/10/05 21:18:50