Spektrum SPM3200 DX3R PRO - Manual (Page 14)

13 SPEKTRUM DX3R PRO USER GUIDE
EN
sErvO sPEEd
The Servo Speed function allows you to change the
speed of any of the three channels—steering, throttle
and Aux. from 100% (default) to 1%. The maximum
speed is 100% and is fixed by the specifications of the
servo itself.
• In the List screen use the roller
to highlight the Servo Speed
function. Press the roller to
access the Servo Speed function.
The Servo Speed screen appears.
• Use the roller to select the
desired channel then press
the roller to access that channel.
Rotate the roller to adjust the
servo speed.
mIxINg
The mixing function allows you to mix any channel
to any other channel. Two mixes are available, Mix
A and Mix B. Both mixes function identically. The
primary or controlling channel is called the master
while the channel mixed to is called the slave. The
slave channel follows the movement of the master
channel. Negative values cause the slave to move in
the opposite direction. The trim is active for both the
master and slave channels.
• In the List screen use the roller
to highlight the Mixing function.
• Press the roller to access.
• Use the roller to select the Mix
you wish to adjust, Mix A or
Mix B.
• Press the roller to highlight that
mix and the surrounding box
will flash. Rotate the roller to
access that mix function.
• Use the roller to highlight the master or slave
channels, then press to access master or slave.
• Use the roller to highlight Value, then press the
roller. Adjust the mix values by rotating the roller.
Independent values can be adjusted by holding the
master channel input (e.g., steering wheel) in the
desired direction and scrolling the roller.
• Mixing values and their proportions can be
observed in the Monitor screen on page 15.
abs
Automatic Braking System (pulse brakes) helps
prevent brake lock-ups and improves braking
performance by pulsing the brakes. The following ABS
braking parameters can be programmed:
State: Inhibit or Active
Point: The throttle position that the pulse braking
takes place. (0 to 100, default is 90)
Stroke: The distance the throttle travels during the
pulse braking. (0 to 100, default is 50)
Lag: The time delay before the pulsing takes place
(0.0 to 2.0 in .1 increments, default is 0.0)
Speed: The pulsing speed or frequency of the pulse
braking. (-1 to -30, default is -1)
The graphic bar at the bottom of the screen displays
the parameters and shows how ABS will function.
Note: State must be Active to turn on the ABS
function.
• In the List screen use the roller
to highlight the ABS function.
• Press the roller to access the
ABS function. The ABS screen
appears.
• Use the roller to select the ABS
parameter you wish to adjust.
• Press the roller to highlight that
parameter and the associated
box will flash. Rotate the roller
to adjust that function.
IdlE uP
Idle up (also called high idle) is used to advance the
throttle position on a gas car during startup to prevent
the engine from dying before the engine is warmed up.
The following Parameters are available:
State: Inhibit or Active
Position: Adjusts the throttle position when idle up
is engaged (0 to 100, default is 0)
Alarm: Activates an alarm when the idle up is active
The graphic bar at the bottom of the screen displays
the parameters and shows how Idle Up will function.
Note: State must be Active to turn on the Idle Up
function.
ABS
User Name
01: Model 01
State: Active
Point: 90
Stroke: 50
Lag: 0.0
Speed: -1
◊
User Name
01: Model 01
Master
Inhibit
Slave
Auxiliary
Value
+0% +0%
Mix a
Servo
Speed
User Name
01: Model 01
ST 100%
TH 100%
AX 100%