Samsung TXT2793HX-XAA - Manual (Page 12)

English - 11
Memorizing the Channels
Your TV can memorize and store all of the available channels for both air and cable
channels. After the available channels are memorized, use the CH and CH button
to scan through the channels. This eliminates the need to change channels by entering
the channel digits. There are three steps for memorizing channels: selecting a broadcast
source, memorizing the channels(automatic) and adding or deleting channels(manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV(i.e. an air or a cable system).
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Storing Channels in Memory (Automatic Method)
3 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
4 Press the ▲ or ▼ button to select the antenna connection, then press the ENTER button.
➢ Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
➢ If you selected “Air”, then go to step 7.
5 Press the ▲ or ▼ button to select Cable, then press the ENTER button.
The cable system menu is displayed .
6 Press the ◄ button, then the ▲ or ▼ button to select the cable system for analog and
digital channels respectively. Press the ► button to select Start, then press the ENTER
button.
➢ If you have Digital cable, select the signal source for both Analog and Digital.
➢ STD, HRC, and IRC identify various types of cable TV systems. Contact your local
cable company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected.
7 After all the available channels are stored, the Auto Program menu reappears.
You can also press the AUTO PROG. button on the remote control to bring up the Auto
Program menu.
Setting the Clock Automatically
9 Press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then the ENTER button.
The message Select the time zone where you are located. is displayed.
10 Press the ▲ or ▼ button to highlight the time zone for your local area.
Press the ENTER button.
If clock is not automatically set, see pages 18~19 to set the clock.
11 The message Enjoy your watching. is displayed.
When you have finished, press the ENTER button.
➢ Even if the ENTER button is not pressed, the message will automatically disappear
after several seconds.
If you want to reset this feature...
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
2 Press the ENTER button to select Plug & Play.
For further details on setting up options, refer to the page 10.
➢ The Plug & Play feature is only available in the TV mode.
Enjoy your watching.
OK
Plug & Play
Set to daylight saving time.
DST Off
On
Move Enter Skip
Plug & Play
Select the time zone where you are located.
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Move Enter Skip
Channel
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
Air
Cable
Move Enter Return
Auto Program
Selects the antenna to execute the Auto
Program function.
Air
Cable
Air + Cable
Start
Start
Start
Move Enter Return
Auto Program
Selects a cable signal type for your
location.
Analog
Start
STD
HRC
IRC
Digital
STD
HRC
IRC
Move Enter Return
Auto Program
Auto Program in Progress.
15%
Air 16
Enter Return
Stop
AA68-03782G_Eng.indd 11 2007-02-21 ｿﾀﾈﾄ 5:16:02