Holtkoetter 2501 - Manual

205 Hardman Avenue South, South Saint Paul, MN 55075
Voice: (800) 899-5444 • Fax: (888) 552-8661
e-mail: [email protected]
www.holtkoetter.com
ASSEMBLY INSTRUCTIONS FOR
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN. Holtkötter ® and Holtkötter Leuchten ® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
Halogen Torchiere with Sidearm
No. 2501
Congratulations, you have purchased one of the finest brass torchieres available on the
market today. Complete with our patented safety device, the ABS-2 Safety™ System, this torchiere
comes with peace of mind.
ABS-2 Safety™ System
The ABS-2 Safety™ System (Automatic Bulb Shut-off) is a revolutionary new electronic safety
system that allows us to continue to do sleek designs, does not disturb the light output and
results in one of the safest lamps that was ever designed and built. If a “critical event” occurs,
the ABS-2 Safety™ System will shut the lamp off. Critical events could be someone accidentally
or intentionally pushing the torchiere over, a drapery covering the glass shield, or the lamp
overheating.
Three independent safety components comprise the ABS-2 Safety™ System:
1. Tilt Shut-off feature
2. Heat Shut-off feature
3. Mechanical Safety Device (round glass plate)
A small, red indicator light shows the safety system is armed. If your lamp shuts itself off as a result
of overheating, please unplug it and allow it to cool for 15 minutes before plugging it back in and
resuming use. This will allow the safety system in the lamp to reset itself.
Included with your Ultimate Lighting Machine™ are halogen bulbs. These long lasting bulbs should
not have to be replaced very often. If you need to change the bulbs, follow the instructions
closely.
Change the Bulb in the Torchiere
1. CAUTION: Always let the glass shield and bulb cool before replacing it. Halogen bulbs
become extremely hot when in use.
2. Carefully remove the glass shield and brackets and set the glass shield in a safe place.
3. Remove the Halopin bulb by pulling it straight out of the socket.
4. Handle the new bulb (maximum 60 Watt/120 Volt Halopin – 5 each) with a soft cloth or
tissue. Halopin bulbs are extremely sensitive to the oils of your fingers and should be installed
without touching the bulb directly.
5. Insert the new bulb by pushing it straight into the socket until it is firmly in place.
6. Replace the glass shield.
Change the Bulb in the Sidearm
1. CAUTION: Always let the glass shield and
bulb cool before replacing it. Halogen
bulbs become extremely hot when in use.
2. Carefully remove the glass shield and
brackets and set the glass shield in a safe
place.
3. Holding one end of the halogen bulb, push
the bulb toward the opposite end of the
socket until that end is out of the socket. Lift
the bulb out of the socket.
4. Handle the new bulb (max. 100 Watt/120
Volt Double-ended Halogen-T3s) with a soft
cloth or tissue. Halogen bulbs are extremely
sensitive to the oils of your fingers and
should be installed without touching the
bulb directly.
5. Put one end of the new bulb into one
socket end and push toward the end
already inserted. Lower the other end into
the socket and the spring mechanism will
hold the bulb in place.
6. Replace the glass shield.
Care Instructions
Use only a soft, dry cloth to clean. If necessary,
a slightly damp, soft cloth may be used to spot
clean.
Do not use common household cleaners or
brass cleaners on lamps or fixtures, as the
lacquer on the outside of the brass may be
damaged as a result.
Enjoy your new Holtkötter lamp.