Kenwood K-511USB-B - Manual (Page 9)

4 7 6 5 3 2 1
8
c
9
i g j h f e d
0
a
b
k
l
m
16 K-511USB/RD-K511USB 17 English
1 K (page 23)
Press to switch the power of the system ON/OFF
(standby mode).
STANDBY/TIMER indicator
Red lighting: Ordinary standby mode
Orange lighting: Timer standby mode
2 CD tray (page 23)
3 VOLUME (page 22)
4 L (page 23)
Press to open or close the CD tray.
5 TUNER (page 44)
Press to switch the radio band between FM/AM.
6 CDE (page 28)
Press to start/pause CD playback.
7 iPod/D.AUDIOE (page 40)
Press to start/pause iPod/D.AUDIO playback.
8 USBE (page 36)
Press to start/pause USB playback.
9 MULTI CONTROL
Press to select a track, fi le or radio station.
Press to fast forward or fast reverse it during
playback.
Press to select a menu item.
ENTER
Press to enter the selected item.
0 SETUP/DEMO
Press to initiate the mode for selecting the function setups.
(page 72-)
Press to switch the demonstration function ON/OFF.
a STOPF
Press to stop playback or recording.
When the TUNER input is selected, press to switch
the tuning mode between auto and manual.
Press during a setup to stop it in the middle.
b USB terminal (page 14)
c AUX (page 42)
Press to select the AUX source.
d CDDUSB (page 52)
Press to start One-Touch Edit recording of CD into
USB.
e CDDSD2 (page 52)
Press to start One-Touch Edit recording of CD into
SD2.
f CDDSD1 (page 52)
Press to start One-Touch Edit recording of CD into
SD1.
Names and functions of parts
Main unit
Read bef
or
e use
g SD2E (page 32)
Press to start/pause SD2 playback.
h SD2 slot (page 23)
Insert an SD card. This slot is used as the AMG
database slot during CD playback.
i SD card illumination
The illumination varies as SD playback/record/move
operation advances.
During playback/pause: Blue (Blinks during pause.)
During recording/record-pause: Red (Blinks during record-
pause.)
During move: Moving red
j SD1 slot (page 23)
Insert an SD card.
k PHONES terminal (page 15)
l SD1E (page 32)
Press to start/pause SD1 playback.
m Display (page 18)
Standby mode
When the [STANDBY/TIMER] indicator is lit, a small
amount of power is supplied to the system to operate
the microcomputer. This status is referred to as the
standby mode. In this state, the system can be switched
OFF from the remote control unit.
One-touch operation function
The system incorporates the convenient one-touch
operation function. When the system is in standby
mode, pressing any of [TUNER], [CD E], [iPod/
D.AUDIO E], [USBE], [AUX], [SD1E] and
[SD2 E] turns the system ON. Playback also starts if a
button related to CD, SD or USB is pressed.
Demonstration function
This system incorporates a demonstration function
(display only). In the demonstration mode, the lighting
operation indicators vary in sequence but this variation
is accompanied with no change in played audio.
To cancel:
Press [SETUP] on the main unit in the middle of
demonstration.
To start:
When the system is ON, press and hold the [SETUP]
button on the main unit for more than 2 seconds.
The demonstration is switched on automatically when a
power failure occurs or the power cord is unplugged or
plugged in again while the system power is ON.
■
■
•
Unifi ed naming on the main unit and remote control unit
In the text describing operations in this manual, the following controls on the main unit and the
remote control unit are expressed as shown below.
[STOP F]
[MULTI CONTROL]
When operation in all of the 4 directions is required: [MULTI CONTROL]
When only the up-down operations are required: [MULTI CONTROL
A/B]
When only the left-right operations are required: [MULTI CONTROL
C/D]
•
•
•