Playing ipod/d.audio, Audio/ video dc in component video d.audio, Playback – Kenwood K-511USB-B User Manual
Page 21: Switching the mode, Button operations during playback/stop

STOP
F
ENTER
DISPLAY/
CHARAC.
iPod/
D.AUDIO
G/H
I/J
MULTI CONTROL
40
K-511USB/RD-K511USB
41
English
Playing iPod/D.AUDIO
An iPod or kenwood digital audio player can be
connected to play audio fi les in it.
For the iPod and kenwood digital audio players that can
be connected to this system, see "Handling iPod" and
"Handling D.AUDIO". (pages 104, 105)
Playback
1
Connect the player.
Connect an iPod or kenwood digital audio player to
the [iPod/D.AUDIO IN] terminal on the rear of the main
unit using a commercially available connection cable.
Y
Cb
Cr
AUDIO/
VIDEO
DC IN
COMPONENT VIDEO
D.AUDIO
kenwood
digital audio player
iPod
PNC-150 (separately
available)
PAD-iP7 (separately
available)
Also read the instruction manual for the connected
component.
2
Select the audio source.
Press [iPod/D.AUDIO
E].
3
Turn the connected player ON and
start playing it.
"
"
is displayed.
While the player is connected to this system, the volume and
tone settings on the player are defeated (* except when an iPod is
connected through PAD-iPod). If the audio level of the connected
iPod/D.AUDIO player is lower or higher than the level at the same
volume control position of other audio sources, adjust the input
level of this system. For how to adjust the input level, see page 69.
•
•
•
Switching the mode
The playback with the iPod/D.AUDIO connection
can be switched between the following two modes.
iPod/D.AUDIO: Use this mode when the connected player
outputs audio only.
iPod/D.AUDIO (BYPASS MODE): Use this mode when the
connected player outputs both video and audio. In this
mode, the audio signal is output without passing through
the DSP (Digital Signal Processor) so that it will not be
delayed with respect to the played video. Note that
recording in SD/USB is not possible in BYPASS MODE.
1
Switching the mode
Press [ENTER].
Each press switches the mode.
Select BYPASS MODE.
Operation in BYPASS MODE
The system cannot set the audio settings other than
the TONE setting.
The record button of the system is defeated.
The mode setting is held even after the audio source
is switched or the system is turned OFF.
Dedicated cable/device for connection
When the separately available PNC-150 (special cable
for kenwood digital audio player connection) or PAD-
iP7 (special cable for iPod connection) is used to
connect the player, the player can be controlled from
the main unit and remote control unit.
For details on the connection and installation, refer to
the manual provided with the PNC-150 or PAD-iP7.
•
•
•
•
•
■
Button operations during
playback/stop
To
Operation
Stop
Press [STOP
F]
during playback.
Pause
Press [iPod/
D.AUDIO
E]
during playback.
Press again to
resume playback.
Skip a folder
Press [MULTI
CONTROL
A/B].
Fast forward/
fast reverse
Press and hold
[
G]/[H]
during playback.
Press and hold
[MULTI CONTROL
C/
D] during playback.
Skip a fi le
Press [CD
H].
Press [MULTI
CONTROL
D].
Return to
previous fi le
Press [
G]
successively twice
or more.
Press [MULTI
CONTROL
C]
successively twice
or more.
Return to the
beginning of
current fi le/
track
Press [
G] once.
Press [MULTI
CONTROL
C] once.
Some control operations may be unavailable depending
on the connected player.
•
Pla
ying music tracks