ididit Retrofit Steering Column: 1967-69 Chrysler B-Body User Manual
Page 5

the dash mount. Make sure there are no
sharp edges in the final piece.
After bolting the wire guard onto the
ididit column you can now attach the
underdash mount to the column.
(figure
8)
Torque the four bolts to 22 ft. lbs.
Disassemble the new floor mount that
was included with your ididit column.
First, install the smaller bracket onto the base
of the column with the raised lip facing the
wheel side. Next, loosely slide the “O” ring
behind the bracket. This will hold the bracket
out of the way while installing the column.
ididit recommends taping the bottom of
the column in order to prevent the paint or
chrome finish from scratching.
(figure 9)
Next, take the Gasket and install it in the
firewall. Then using the four bolts and
washers that were provided, loosely install
the floor mount making sure that the lip is
facing out.
(figure 10)
Locate the three nuts that hold the column
to the dash. If you haven’t done this yet,
check the lower shaft of the column and
pull the shaft outward about 2 inches and
then quickly slide it back in. This will
3
Figure 8
Figure 9
FLAIR EDGE
3 3/4”
3/8”
Figure 7
Figure 10
- Universal Steering Column: How To Measure An ididit Steering Column (2 pages)
- Universal Steering Column: Universal Tilt (8 pages)
- Universal Steering Column: Universal Shorty Tilt (8 pages)
- Universal Steering Column: Universal Straight (8 pages)
- Universal Steering Column: Old School Straight Column (4 pages)
- Universal Steering Column: Old School Straight Horn Kit (4 pages)
- Retrofit Steering Column: Tri-Five Chevy (18 pages)
- Retrofit Steering Column: 1970-75 Camaro (12 pages)
- Retrofit Steering Column: 1962-66 Nova (12 pages)
- Retrofit Steering Column: 1955-59 Chevy Truck (12 pages)
- Retrofit Steering Column: 1965-66 Mustang (8 pages)
- Retrofit Steering Column: 1967 Mustang (8 pages)
- Retrofit Steering Column: 1968-69 Mustang (8 pages)
- Retrofit Steering Column: 1965 Falcon (12 pages)
- Retrofit Steering Column: 1965 Mercury Comet (8 pages)
- Retrofit Steering Column: 1965-66 Ford Truck (8 pages)
- Retrofit Steering Column: 1967-72 Ford Truck (8 pages)
- Retrofit Steering Column: 1973-77 Ford Truck (8 pages)
- Retrofit Steering Column: 1978-79 Ford Truck (8 pages)
- Retrofit Steering Column: 1974-77 Ford Bronco (8 pages)
- Retrofit Steering Column: 1976-86 Jeep CJ5 & CJ7 (12 pages)
- Retrofit Steering Column: Jeep Column to a Painless Wiring Kit (1 page)
- Retrofit Steering Column: 1970-74 Cuda/Challenger (12 pages)
- Retrofit Steering Column: 1970-74 Cuda/Challenger Ignition Switch (1 page)
- Retrofit Steering Column: 1970-74 Cuda/Challenger Wheel Adaptor (1 page)
- Retrofit Steering Column: 1968 Chrysler B-Body Adaptor Plug (1 page)
- Retrofit Steering Column: 1973 Chrysler B-Body (12 pages)
- Right Hand Drive & Collapsible Steering Column: Theory of a Collapsible Column (2 pages)
- Right Hand Drive & Collapsible Steering Column: RHD Universal Tilt (8 pages)
- Right Hand Drive & Collapsible Steering Column: RHD Tri-Five Chevy (16 pages)
- Right Hand Drive & Collapsible Steering Column: RHD 1965-66 Mustang (8 pages)
- Right Hand Drive & Collapsible Steering Column: RHD 1968-69 Mustang (8 pages)
- Golf Cart Steering Column: Club Car (1 page)
- Golf Cart Steering Column: E-Z Go (1 page)
- Golf Cart Steering Column: Yamaha (2 pages)
- Golf Cart Steering Column: Golf Cart 9-Bolt Steering Wheel Adaptor (1 page)
- Golf Cart Steering Column: Flasher Kit (1 page)
- Golf Cart Steering Column: Golf Cart Wiring (1 page)
- Steering Wheel Adaptor: Basic Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Standard Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Bell Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Bell/Grant Wheel w/Horn Kit (1 page)
- Steering Wheel Adaptor: 9-Bolt Shorty Adaptor (1 page)
- Steering Wheel Adaptor: 1953-66 Corvette Adaptor (1 page)