beautypg.com

6 pcipnp pcipnp pcipnp pcipnp pcipnp, Reset configuration data [disabled, Resources controlled by [auto – Asus NCCH-DR User Manual

Page 91: Pci/vga pallete snoop [disabled, Int pin 1~8 assignment [auto

background image

A S U S N C C H - D R

A S U S N C C H - D R

A S U S N C C H - D R

A S U S N C C H - D R

A S U S N C C H - D R

4 - 2 9

4 - 2 9

4 - 2 9

4 - 2 9

4 - 2 9

4.4.6

4.4.6

4.4.6

4.4.6

4.4.6

PCIPnP

PCIPnP

PCIPnP

PCIPnP

PCIPnP

This menu shows the PCIPnP configuration settings. Select an item then
press to display a pop-up menu with the configuration options.

Reset Configuration Data

[Disabled]

Resources Controlled By

[Auto]

IRQ Resources

PCI/VGA Pallete Snoop

[Disabled]

INT Pin 1 Assignment

[Auto]

INT Pin 2 Assignment

[Auto]

INT Pin 3 Assignment

[Auto]

INT Pin 4 Assignment

[Auto]

INT Pin 5 Assignment

[Auto]

INT Pin 6 Assignment

[Auto]

INT Pin 7 Assignment

[Auto]

INT Pin 8 Assignment

[Auto]

PCIPnP

Select Menu

Item Specific Help

Default is Disabled.
Select Enabled to reset
Extended System
Configuration Data
(ESCD) when you exit
Setup, if you installed
a new add-on card and
the system
reconfiguration has
caused a serious
conflict that the OS
cannot boot.

Reset Configuration Data [Disabled]

Reset Configuration Data [Disabled]

Reset Configuration Data [Disabled]

Reset Configuration Data [Disabled]

Reset Configuration Data [Disabled]

Allows you to enable or disabled resetting of the Extended System
Configuration Data (ESCD) when you exit the Setup. The ESCD includes
information on non-PnP devices. Set this item to [Enabled] if you installed
an expansion card that conflicts with other devices and cause system boot
failure. Configuration options: [Disabled] [Enabled]

Resources Controlled By [Auto]

Resources Controlled By [Auto]

Resources Controlled By [Auto]

Resources Controlled By [Auto]

Resources Controlled By [Auto]

When set to [Auto(ESCD)], allows BIOS to automatically configure of all
boot and Plug and Play devices. When set to [Manual], you can assign the
available IRQ Resources to the PCI devices.
Configuration options: [Auto] [Manual]

When the item R e s o u r c e s C o n t r o l l e d B y

R e s o u r c e s C o n t r o l l e d B y

R e s o u r c e s C o n t r o l l e d B y

R e s o u r c e s C o n t r o l l e d B y

R e s o u r c e s C o n t r o l l e d B y is set to [Auto], the item

IRQ Resources is grayed out and not user-configurable. Refer to the
section “IRQ Resources” for information on how to enable this item.

PCI/VGA Pallete Snoop [Disabled]

PCI/VGA Pallete Snoop [Disabled]

PCI/VGA Pallete Snoop [Disabled]

PCI/VGA Pallete Snoop [Disabled]

PCI/VGA Pallete Snoop [Disabled]

Some non-standard VGA cards, like graphics accelerators or MPEG video
cards, may not show colors properly. Setting this field to [Enabled] corrects
this problem. If you are using a standard VGA card, leave this field to the
default setting [Disabled]. Configuration options: [Disabled] [Enabled]

INT Pin 1~8 Assignment [Auto]

INT Pin 1~8 Assignment [Auto]

INT Pin 1~8 Assignment [Auto]

INT Pin 1~8 Assignment [Auto]

INT Pin 1~8 Assignment [Auto]

Allows you to select the appropriate interrupt to the specific devices to
avoid conflict. Configuration options: [Auto] [3] [4] [5] [7] [9] [10] [11]
[12] [14] [15]