Asus NCCH-DR User Manual
Page 49
A S U S N C C H - D R
A S U S N C C H - D R
A S U S N C C H - D R
A S U S N C C H - D R
A S U S N C C H - D R
2 - 2 9
2 - 2 9
2 - 2 9
2 - 2 9
2 - 2 9
4 .
4 .
4 .
4 .
4 .
Serial ATA RAID connectors (7-pin SATA_RAID1,
Serial ATA RAID connectors (7-pin SATA_RAID1,
Serial ATA RAID connectors (7-pin SATA_RAID1,
Serial ATA RAID connectors (7-pin SATA_RAID1,
Serial ATA RAID connectors (7-pin SATA_RAID1,
S A
S A
S A
S A
S ATA_RAID2, SATA_RAID3, SATA_RAID4)
TA_RAID2, SATA_RAID3, SATA_RAID4)
TA_RAID2, SATA_RAID3, SATA_RAID4)
TA_RAID2, SATA_RAID3, SATA_RAID4)
TA_RAID2, SATA_RAID3, SATA_RAID4)
On SATA models only
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the Adaptec AIC-8130 SATA RAID controller.
Before creating a RAID set using Serial ATA hard disks, make sure that
you have connected the Serial ATA signal cable and installed Serial ATA
hard disk drives; otherwise, you cannot enter the RAID utility and SATA
BIOS setup during POST.
5 .
5 .
5 .
5 .
5 .
H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
For some storage cards, such as SCSI card, with access signals for
external LEDs, this connector allows the access signals to go through
the front panel IDE_LED lead.
NCCH-DR
NCCH-DR SATA RAID connectors
SATA_RAID4
SATA_RAID3
SATA_RAID2
SATA_RAID1
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXP5
RSATA_RXN5
GND
GND
RSATA_TXP6
RSATA_TXN6
GND
RSATA_RXP6
RSATA_RXN6
GND
NCCH-DR
NCCH-DR
SCSI/SATA card activity LED connector
HDLED1
1
ADD_IN_CARD_ACT#
NC
NC
ADD_IN_CARD_ACT#