Hired-Hand Mega Flow SlantWall Fans: UNASSEMBLED BELT DRIVE METAL FAN 48 & 52 Slant Wal - Manual

Hired-Hand, Inc.
• 1733 County Road 68 • Bremen, Alabama 35503 • Ph 256-287-1000 • Fax 256-287-2000
Manual Part No. 4801-2993 Rev 9-05 Page 1 of 4
Please Read And Understand All Steps Of Instructions Before Assembly
1. Refer to Detail A and assemble the Sheave Idler Pulley
(1011-9005) to the Belt Tension Bracket (0404-4665)
with Cap Screw (1004-1426) and Screw (1004-6020) as
shown. Set the assembly aside until Step 4.
2. Refer to Detail B. Place Top Brace (0404-4648) on top of
the Bottom Brace (0404-4647) and align holes.
3. Place the two Bearing Pillows (1016-0100) on the Top
Brace and bolt with 3/8" cap screw (1004-3054), flat
washers (1003-1462) and lock nuts (1001-1457). Tighten
securely.
4. Install the idler pulley assembly prepared in Step 1.
5. Install the gusset to the top corner of the Top Brace as
shown in Detail C.
TOOLS REQUIRED
Ratchet Torque wrench
6" (152 mm) Ratchet extension 5/32" (4 mm) Allen head socket
9/16" (14 mm) socket 1/8" (3 mm) Allen head socket
7/16" (11 mm) socket Rubber mallet
1/2" (13 mm) socket Flat head screwdriver
Electric or cordless drill Pop rivet gun
3/8" (10 mm) Socket head bit 9/16" (14 mm) open end box end wrench
3/8" (10 mm) Socket -12pt. star 7/16" (11 mm) open end box end wrench
2' (61 cm) scale or carpenter's square Needle nose pliers
WARNING!
Do Not Connect Electrical Power
Until Assembly Is Complete
Always Double Check Power Sources!
CAP Screw
5/16-18 X 1”
(1004-1414)
Flat Washer
5/16” X ¾”
(1003-0103)
Lock Nut
5/15 “-18
(1001-1735)
Detail C
Motor Mount
Gusset
Idler Pulley
Assembly
(6403-9201)
Flat Washer
3/8” X 1 O.D
(1003-1462).
Flat Washer
3/8” X 1 O.D.
(1003-1462)
Lock Nut 3/8”
x 1O.D.
(1001-1457)
Detail B
Lock Nut
¼” x 20
(1001-1446)
CAP Screw
¼” X 20 X ¾”
(1004-1402)
Flat Washer
¼” USS
(1003-1461)
Bearing Pillow
(1016-0100)
Cap Screw
3/8” X 16 X 1 ½”
(1004-3054)
Side of brace
not shown
for clarity.
Top Brace
(0404-4648)
Bottom Brace
(0404-4647)
Idler Pulley
(1011-9005)
Belt Tension Bracket
(0404-4665)
Detail A
Screw ¼” - 20 X 3/8”
(1004-6020)
Cap Screw
3/8” – 16 X 1”
(1004-1426 )
48" & 52”
Slant Wall
MEGA-FLOW
®
U N A S S E M B L E D B E L T D R I V E M E T A L F A N