Throttle motor assembly instructions – SaltDogg SCH096 Series Self-Contained Hopper Spreader User Manual
Page 10

Quality since 1946
THROTTLE MOTOR ASSEMBLY
INSTRUCTIONS
Caution! Improper installation of the Throttle Motor
Assembly can result in damage to the engine choke/throt-
tle linkage.
Removal Instructions:
1.
Carefully observe the existing installation and mark the
position of the Throttle Control Bracket on the Engine
Mount Stand.
2
.
Disconnect the wire connections.
3.
Remove the 1/4-20 fasteners that hold the Throttle
Control Bracket to the Engine Mount Stand. Remove the
Throttle Motor Assembly.
Installation Instructions:
1.
Connect the electrical wiring. Only connect the brown
wire to brown (white) wire and red wire to red (black) wire.
2
.
Fasten the new Throttle Motor to the Throttle Control
Bracket using the existing hardware.
3.
Run the new Throttle Motor until the crank is within
opening of the Throttle Control Bracket.
4.
Place the Throttle Pin Assembly on the crank of the
Throttle Motor using hole in the end of plastic block.
5.
Place the assembly onto the Engine Mount Stand by
inserting the Throttle Pin into the engine choke/throttle
linkage slider.
6.
Keeping the Throttle Pin Assembly parallel to the
engine choke/throttle linkage bolt the assembly to the
Engine Mount Stand with the existing hardware.
7.
Run Throttle Motor in both directions until the slider in
choke/throttle linkage stops against choke/throttle linkage
bracket. Adjust position of Throttle Bracket if necessary.
10
1
3005788
1
ENGINE MOUNT WELDMENT CS
1
3005734
1
ENGINE MOUNT WELDMENT SST
2
141070K
1
GEARBOX ASSEMBLY
1401200
1
GEARBOX, 20:1
1410702
1
SPROCKET, 16 TOOTH
K18N
1
KEY, WOODRUFF 1/4” x 1-1/8”
3
1401150
1
CLUTCH ASSEMBLY
4
K18N
1
KEY, WOODRUFF 1/4” x 1-1/8”
5
1411000
1
BEARING, 2-HOLE FLANGED, 1” ID
6
1411800
1
SPROCKET, CLUTCH, 52 TOOTH
7
3005828
1
ENGINE SHROUD WELDMENT CS
7
3005826
1
ENGINE SHROUD WELDMENT SST
8
3001361
2
WASHER, FLAT 3/8” ID NYLON
9
1410707
1
BATTERY, 12 VDC
10
3001363
2
BRACKET, BATTERY MOUNT
11
1410216
SPONGE RUBBER
12
4
SCREW, HHC 1/2-13 X 1 GR 5
13
4
WASHER, LOCK 1/2”
14
1411500
2
COLLAR, 1” ID
15
2
SCREW, HHC 5/16-18 X 1-1/2 GR 5
16
2
WASHER, FLAT 5/16 SAE
17
3005735
1
ENGINE ASSEMBLY, TECUMSEH 10 HP
18
3000283
2
PIN, PIVOT, 5/32 X 1-1/2”
19
3
SCREW, HHC 5/16 - 18 X 5/8”
20
4
BOLT, CARRIAGE 3/8-16 X 1”
21
6
WASHER, FLAT 3/8 USS
22
4
WASHER, LOCK 3/8”
23
4
NUT, HEX 3/8-16
24
2
NUT, HEX NYLOCK 3/8-16
25
2
SCREW, HHC 3/8-16 X 1-1/4” GR 5
26
5
WASHER, LOCK 5/16”
27
2
NUT, HEX 5/16-18
28
3001381
1
GUARD, ENGINE BASE CS
29
3000281
2
STRAP, RUBBER LATCH
30
2
WASHER, FLAT #8
31
3000285
2
E-RING, 5/32
32
7
SCREW, HHC 1/4-20 X 3/4 GR 5
33
7
NUT, NYLOCK 1/4-20
34
6
WASHER, FLAT 1/4” SAE
35
1412300
1
CHAIN, #40 ROLLER, 78 PITCHES
36
1413200
1
GROMMET, 1-1/2” RUBBER
ITEM
PART NO.
QTY.
DESCRIPTION
R
Re
ep
pa
aiirr P
Pa
arrtts
s -- D
Drriiv
ve
e S
Su
ub
ba
as
ss
se
em
mb
blly
y