beautypg.com

Paasche Airbrush A-US User Manual

Uts, ups-1 and a-us, Manual and automatic stripers

background image

UTS, UPS-1 and A-US

Manual and Automatic Stripers

OPERATING INSTRUCTIONS & REPLACEMENT PARTS

WARNING: Striping materials may be harmful if inhaled or

allowed to come into contact with the skin or eyes. Consult

the product label and Material Safety Data Sheet supplied

for the spray material. Follow all safety precautions.

CAUTION: Well Ventilated Area Required to remove

fumes, dust or overspray. Secure airhose and fluid

hose wrench tight for safety and to prevent leaks.

M a x i m u m A i r P r e s s u r e 1 0 0 P . S . I .

M a x i m u m F l u i d P r e s s u r e 4 5 P . S . I .

INSTRUCTIONS AND PARTS LIST UTS-UPS-8/31/2011

Supersedes Instructions & Parts List UTS-UPS-5/29/09

OPERATING INSTRUCTIONS:

1. Paasche Universal Stripers can be used with or without

adjustable swivel guide assembly.

2. The flow of fluid is controlled by UH-307 Stroke Adjusting

Screw (Item 15) for UTS Thumb-Action Striper. U-2061
Stroke Control Screw (Item 19) for UPS-1 Pistol Grip Striper.
U-3178 Fluid Adjusting Knob (Item 26) for A-US Auto matic
Striper; which regulates the stroke of the fluid needle.

3. A light pressure with finger or thumb lever (UTS- and

UPS-1) provides flow of material.

4. A Gravity Cup is normally used when material is of such

consistency that it will flow readily.

a. Raised or embossed effect may also be obtained by

using a pressure plunger cup or pressure feed
material tank with hose.

b. When using a pressure feed tank unit, a small supply of

compressed air is required to feed the fluid to the striping nib.

5. Standard flow nibs fit various widths and shapes of

grooves.

a. Multiple striping nibs are made to order.
b. These nibs are made from Oil Hardening Drill Rod

and Flame hardened for durability.

c. A sample of article to be decorated or striped should

be sent to factory for determining suitable type nib
when special nibs are required.

DIRECTIONS:

1. Any liquid colors or fluid of proper consistency may be used.
2. Special striping lacquer or colors are manufactured and

will give better results.

a. Use as directed by Manufacturer.
b. IMPORTANT: all fluids should be mixed to free flowing

consistency according to your requirements.

3. When using a Manual Striper with a Gravity Feed Cup the

color should flow from Tip of Nib at a rate of approximately
one drop per second, at proper fluid consistency.

a. If consistency of fluid is too heavy it will cause flow of

material to be retarded or skip.

b. If consistency of fluid is too thin, it will blur or run.
c. To adjust the flow of fluid, suitable for work to be

done, turn:

• UH-307 Stroke Adjusting Screw (Item 15) for the

UTS Thumb-Action Striper.

• U-2061 Stroke Control Screw (Item 19) for the UPS-

1 Pistol Grip Striper.

• U-3178 Fluid Adjusting Knob (Item 26) for the A-US

Automatic Striper.

d. Practice on a smooth board or flat metal surface.
e. Striper should be in motion before trigger is

depressed.

f. Then proceed to stripe at even speed.
g. After a little practice you will be able to stripe uniformly

at any speed over smooth or rough surfaces.

4. For obtaining a raised or embossed effect, for filling in

grooves or doing overhead work, heavy fluid materials
are used with a pressure plunger cup or pressure fluid
tank to feed the fluid color.

a. Pressure should be regulated to give the desired flow of

material at the tip. (Maximum Fluid Pressure 45 P.S.I.)

b. This flow will vary in accordance with the consistency

of the fluid and the effect desired.

CLEANING:

1. Place the color nib in solvent cup between operating

periods to prevent color from drying.

2. Before use, wipe nib with cloth to remove solvent

accumulation and help color to start flowing.

3. Clean cup thoroughly and wash out nib and fluid body in

solvent before putting away.

4. Keep vent hole in top of color cup open.

INFORMATION:

Paasche precision made Units and Striping guns are
designed and manufactured for quality striping and the
highest production at lowest cost.
Special striping requirements mean special equipment.
Paasche designs special Semi-Automatic and Automatic
Strip ing Units. These Units are convertible in design and
application of limitless materials, for use with lacquers or
any color fluid mixed to a free flowing consistency. Available
with Nibs that control lines from fine to wide, at any desired
speed, depending on size used. These Units can be used
for striping, decorating, edging or coloring flat, concave or
convex surfaces and routings. They are excellent for
applying liquid latex, paste, glue or similar materials.
For more information regarding Paasche Striping guns,
Semi-Automatic or Automatic Units contact the Paasche
Sales Department located at the Main Office.

Paasche Airbrush Company

4311 North Normandy Avenue

Chicago, IL 60634-1395

Phone: 773-867-9191 • Fax: 773-867-9198

Website: paascheairbrush.com

E-Mail: [email protected]

Printed in the U.S.A.

This manual is related to the following products: