AMX Modero ViewPoint MVP-8400 - Manual (Page 155)

Programming
141 MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Miscellaneous MVP Strings back to the Master
The following two strings are sent by the MVP panel back to the communicating Master:
"^" Button Commands (Cont.)
^TXT
Assign a text
string to those
buttons with a
defined address
range.
Sets Non-Unicode text.
Syntax:
"'^TXT-,,'"Variable: variable text address range = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).new text = 1 - 50 ASCII characters.Example:SEND_COMMAND Panel,"'^TXT-500.504&510.515,1&2,Test Only'"Sets the On and Off state text for buttons with the variable text ranges of
500-504 & 510-515.^UNISet Unicode text.For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as
ASCII-HEX nibbles. Syntax: "'^UNI-,,'"Variable: variable text address range = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).unicode text = Unicode HEX value. Example:SEND_COMMAND Panel,"'^UNI-500,1,0041'"Sets the button’s unicode character to ’A’.
Note: To send the variable text ’A’ in unicode to all states of the variable text
button 1, (for which the character code is 0041 Hex), send the following command: SEND_COMMAND TP,"'^UNI-1,0,0041'"Note: Unicode is always represented in a HEX value. TPD4 generates (through the Text
Enter Box dialog) unicode HEX values. Refer to the TPDesign4 Instruction Manual for
more information.^VTPSimulates a
touch/release/
pulse at the given
coordinate.Syntax:^VTP-<0=Release, 1=Press, 2=Pulse>,,MVP Strings to Masterundock This is sent to the target Master when the MVP is undocked.• If the panel has no information within the User Access Passwords list, ’none’ is sent as a user.• If the undock button on the Protected Setup page is used, ’setup’ is sent as a user.• This string can be disabled from within the firmware setup pages.dockThis is sent to the target Master when the MVP is docked.• This string can be disabled from within the firmware setup pages.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^TXT-500.504&510.515,1&2,Test Only'"
Sets the On and Off state text for buttons with the variable text ranges of
500-504 & 510-515.
^UNI
Set Unicode text.
For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as
ASCII-HEX nibbles.
Syntax:
"'^UNI-,
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
unicode text = Unicode HEX value.
Example:
SEND_COMMAND Panel,"'^UNI-500,1,0041'"
Sets the button’s unicode character to ’A’.
Note: To send the variable text ’A’ in unicode to all states of the variable text
button 1, (for which the character code is 0041 Hex), send the following command:
SEND_COMMAND TP,"'^UNI-1,0,0041'"
Note: Unicode is always represented in a HEX value. TPD4 generates (through the Text
Enter Box dialog) unicode HEX values. Refer to the TPDesign4 Instruction Manual for
more information.
^VTP
Simulates a
touch/release/
pulse at the given
coordinate.
Syntax:
^VTP-<0=Release, 1=Press, 2=Pulse>,,
MVP Strings to Master
undock This is sent to the target Master when the MVP is undocked.
• If the panel has no information within the User Access Passwords list, ’none’ is sent as
a user.
• If the undock button on the Protected Setup page is used, ’setup’ is sent as a user.
• This string can be disabled from within the firmware setup pages.
dock This is sent to the target Master when the MVP is docked.
• This string can be disabled from within the firmware setup pages.