Control Company 5011 GIANT-DIGIT COUNTDOWN TIMER - Manual

SPECIFICATIONS
Timing Capacity:
99 minutes, 59 seconds
Timing Accuracy: ±0.01%
COUNTDOWN ALARM TIMING
1.
Clear the display to zero.
2. Press the MIN (minutes) button to advance the minutes digits. Press and
hold down the MIN button to rapidly advance the minutes.
3. Press the SEC (seconds) button to advance the seconds digits. Press and
hold down the SEC button to rapidly advance the seconds.
4. Once the desired time is on the display, press the START/STOP button to
begin countdown timing.
5. When the timer reaches zero, an alarm will sound and the timer will begin
counting up.
The alarm will sound for one minute and then turn off automatically to preserve
battery life while the timer continues counting up.
While the alarm is sounding, pressing the START/STOP button will silence the
alarm, stop the count-up timing, and recall the last programmed time. After one
minute, pressing the START/STOP button will stop the count-up timing and recall
the last programmed time.
MEMORY RECALL
When timing repetitive intervals, the memory function will recall the last
programmed time. This feature allows the timer to be dedicated to a frequently
timed test. The timer will return to the last programmed time again and again.
1.
Follow steps 1 through 5 in the “Countdown Alarm Timing” section.
2. When the alarm starts, press the START/STOP button to stop the alarm
and recall the last programmed time.
3. Press the START/STOP button a again to begin countdown timing.
CLEARING THE DISPLAY TO ZERO
If an error is made during an entry, press the MIN and SEC buttons
simultaneously to clear the display to zero. If you wish to clear the display to zero
when time is running, you must first stop the timing by pressing the START/STOP
button, then press the MIN and SEC buttons simultaneously. The timer will only
clear when time is stopped.
STOPWATCH (COUNT-UP) TIMING
1.
Clear the display to zero.
2. Press the START/STOP button to begin count-up timing.
3. Press the START/STOP button to stop count-up timing.
Once timing is completed and the timer has been stopped, press the MIN and
SEC buttons simultaneously to clear the display to zero.
TIMEOUT
The timer may be stopped during any running time by pressing the START/STOP
button. Timing may be resumed by pressing the START/STOP button a second
time.
CONVERT A TIMEOUT TO A COUNTDOWN TIME
The timer may be stopped during any running time (countdown or count-up) by
pressing the START/STOP button. Once the timing has been stopped, pressing
the MIN or SEC button will increment the display from the point that it was
stopped and will set the timer into countdown mode. Once the desired time is on
the display, press the START/STOP button to begin countdown timing.
ALL OPERATIONAL DIFFICULTIES
If this timer does not function properly for any reason, replace the battery with a
new high quality battery (see the “Battery Replacement” section). Low battery
power can occasionally cause any number of “apparent” operational difficulties.
Replacing the battery with a new fresh battery will solve most difficulties.
BATTERY REPLACEMENT
An incorrect display, no display or operational difficulties indicate that the battery
should be replaced. Slide open the battery cover on the back of the timer. Insert
a new AAA alkaline battery. Make certain to note the proper polarity as indicated
by the diagram in the battery compartment. Replace the battery cover.
Warranty, Service, or Recalibration
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714
Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-Certified by
DNV and ISO 17025 accredited as a Calibration
Laboratory by A2LA.
Control Company Cat. No. 5011
Traceable
® is a registered trademark of Control Company
© 2008 Control Company 92-5011-00
TRACEABLE
®
GIANT-DIGIT
™
COUNTDOWN TIMER INSTRUCTIONS