Control Company 5020 Mini-Alarm-Timer/Stopwatch - Manual

SPECIFICATIONS
Display:
½"-High LCD showing minutes and
seconds
Accuracy: 0.01%
Timing
Capacity:
Count down – 1 second to 99 minutes,
59 seconds Count-up – 1 second to
59 minutes, 59 seconds.
Alarm: Audible alarm sounds for one minute
Functions: Countdown timing and count-up
(stopwatch) timing
Attachments: Clip, magnetic back, and stand
Size:
2½" x 2¼" x ½"
Weight: 1.5 oz
COUNTDOWN TIMING
1. Press the STOP/RESET button to set timer to
zero. The display should read 00:00.
2. Press the numbers keys 0 through 9 to set
desired minutes and seconds. (Example: to set
12 minutes 38 seconds, press 1, 2, 3, 8.)
Note: To time in seconds only, press just two of the
number keys. (Example: To set 15 seconds, press
keys 1 and 5.)
3. If the wrong time has been entered, press the
STOP/RESET button to return the display to
00.00.
4. Once the desired time is on the display, press
the START button to begin countdown timing.
5. When the timer reaches 00:00, an alarm will
sound. The alarm will sound for 60 seconds and
then turn off automatically. To turn the alarm off
manually, press any button or number key.
Note: The display will read 00.00 during the 60
second alarm sounding time and after the alarm is
turned off.
6. During the countdown process, the timer may be
paused by pressing the STOP/RESET button one
time and restarted by pressing the START
button.
Note: Pressing the STOP/RESET button twice, will
clear the display and return it to 00.00.
STOPWATCH (COUNT-UP) TIMING
1. Press the STOP/RESET button to set the timer to
zero. The display should read 00.00.
2. Press the START button once to begin count-up
timing.
Note: Timer will count up to 59 minutes, 59 seconds
and then automatically reset itself to zero – the
display will read 00.00 for one second and then start
counting up
3. During the count-up process, the timer may be
paused by pressing the STOP/RESET button one
time and restarted by pressing the START
button.
Note: Pressing the STOP/RESET button twice, will
clear the display and return it to 00.00.
Mini-Alarm-Timer/ Stopwatch Instructions
4. To end the count-up process at any time, press the
STOP/RESET button twice.
TIMEOUT
The timing process may be stopped at any time
during count-up or countdown. Press the
STOP/RESET button one time. Timing may be
resumed by pressing the START button.
Note: Pressing the STOP/RESET button twice, will
clear the display and return it to 00.00.
All Operational Difficulties
If this timer does not function properly for any reason,
please replace the battery with a new high quality
battery (see “Battery replacement” section). Low
battery power can occasionally cause any number of
“apparent” operational difficulties. Replacing the
battery with a new fresh battery will solve most
difficulties.
Battery Replacement
An incorrect display, no display or operational
difficulties indicate that the battery should be
replaced. Use a coin to open the battery cover on the
back of the timer (turn the cover approximately 1/8 of
a turn counter-clockwise). Equivalent battery
replacements are: RAYOVAC RW42, DURACELL
D357, GPA76, and EVEREADY 357. Insert the battery
with the positive side facing you. Replace the battery
cover. Replacement battery Cat. No. 1039.
WARRANTY, SERVICE, RECALIBRATION
For warranty, service or recalibration contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-
Certified by DNV and ISO 17025
accredited as a Calibration Laboratory
by A2LA.
Cat. No. 5020
Traceable ® Mini-Alarm-Timer/Stopwatch Instructions
92-5020-00
Rev. 0 040705
Traceable ® is a registered trademark of Control
Company
© 2005 Control Company