beautypg.com

CognitiveTPG A760 User Manual

Page 25

background image

Chapter 3: Setting up the Printer

25

A760-D100 10/04

189-9200303 Rev. D A760 Two-Color Thermal/Impact Hybrid Printer: User Guide

*** A760 - Diagnostics Form ***

*** A760 - Diagnostics Form ***

Model number

: A760-1125

Serial number

: A012451679

Boot Firmware

Revision

: V1.03

CRC

: FFDE

P/N

: 189-7600118A

Flash Firmware

Revision

: V1.05

CRC

: 7196

P/N

: 189-7600117A

H/W parameters

Flash Memory Size

: 1 Mbyte

Flash Logos/Fonts

: 320 kbytes

Flash User Storage

: 0 kbytes

SRAM Size

: 256 kbytes

Head setting

: D

Paper Type Name

: Type 1, Version 0

Color Density Adj

: 100 %

Print Density (Mono) : 100 %

Max Speed

: 100 mm/sec

Max Power

: 55 W

Alternate Reset

: Disabled

Knife

: Enabled

Paper Low Sensor

: Enabled

MICR

: Enabled

MICR Dual Pass

: Disabled

MICR DC offset

: 80

Check Flip

: Enabled

Comm. Interface

RX Buffer Size

: 4096

Interface type

: RS232/USB

Parameters

Baud Rate

: 115200

Data Bits

: 8

Stop Bit

: 1

Parity

: NONE

Flow Control

: DTR/DSR

Reception Errors

: Ignore

Alternate DTR/DSR : Disabled

Resident Code Pages

: 437, 850, 852. 858

860, 863, 865, 866

1252,862, 737

Available Paper Types

:

00.00 01.00 05.00

Logo(s) defined

: YES

User Char(s) defined

: NO

To enter Printer Config Menu :

1) Flip DIP switch #1 up

2) Reset the printer, while holding

the Paper Feed button down

***

***

A760 - Printer Config Menu

A760 - Printer Config Menu

***

***

This config menu allows you to set general printer

parameters

Sub-menus are entered and selections are made using

the Paper Feed Button

- short click : Feed Button is quickly depressed

then released

- long click : Feed Button is held down more than

1 second then released

CAUTION !!

CAUTION !!

The settings are predetermined in factory and

should generally not be changed.

If you must change the settings do so carefully

to avoid changing other functions.

****************

********

MAIN MENU

MAIN MENU

********

**************************

Select a sub-menu :

- EXIT

-> 1 click

- Print Current Configuration

-> 2 clicks

- Set Communication Interface

-> 3 clicks

- Set Diagnostics Modes

-> 4 clicks

- Set Emulation/Software Options -> 5 clicks

- Set Hardware Options

-> 6 clicks

- Set Paper Type

-> 7 clicks

Enter code, then hold Button DOWN

at least 1 second to validate

Important: Ensure that the

configuration settings match

your host computer, if not,

enter the configuration menu

to make changes.

}

Current printer tallies are

printed after the diagnostic

information and will vary

per printer use.

Sample diagnostic menu and print test for serial connection(show approximately 60% of size). Ethernet diagnostic

printout not shown. Ethernet parameters can not be changed in the configuration menu.

When the printer is configured
for USB and the native USB
solution driver is used, this
location will show either: “USB
Driver Type: TPG, Inc.” or “USB
Driver Type: Printer Class”.

If the RS-232C, USB emulation
solution driver is used, nothing
is printed here. See User Guide,
Appendix A.

Paper type can be changed
in the configuration menu.
Paper types and grades
available:

Type 0 - Monochrome grades

Kanzaki P-310

Type 1 - Two-color grades

Kanzaki P-310 RB

Type 4 - Two-color grades

Kanzaki P-310 BB

Type 5 - Two-color grades

Kanzaki P-320 RB

See page 48 and Programming
guide for more information.