CNB PM1063P - Manual (Page 15)

◎ Setup the general functions of Pan/Tilt motions.
• MOTION LOCK [ON/OFF]
- If Motion Lock is set to ON, it is impossible to set
up and delete Preset, Swing, Pattern and Group.
It is possible only to run those functions. To set
up and delete those functions, enter into OSD
menu.
• PWR UP ACTION [ON/OFF]
- Refer to “Other Functions" section.
• FRZ IN PRESET [ON/OFF]
- At start point of preset movement, camera starts freezing the image of start point.
Camera keeps displaying the image of start point during preset movement and does
not display the images which camera gets during preset movement. As soon as
camera stops at preset end point, camera starts displaying live images which it gets at
preset end point. This function availability should be different by models.
◎ When the camera position is changed by the
outside pressure, perform the auto calibration.
• CALIBRATION [AUTO/OFF]
- Case 1 : System boot and menu setting up
(executes 2 times Calibration)
- Case 2 : Normal operation (executes 10 times
Calibration (within 5 minutes))
- If “Case 1” or “Case 2” are occurred,
Calibration is Changed to “OFF”. And
“CALIBRATION OFF” Message is displayed.
- Using Controller, If “NEAR” command is received, “CALIBRATION OFF” message is
removed.
- After Auto Calibration, executes the last action.
◎ Setup the Jog speed and Direction.
• AUTO FLIP [ON/OFF]
- Refer to “Other Functions" section.
• JOG MAX SPEED [1 °/sec~200°/sec]
- Sets maximum jog speed. Jog speed is inversely
proportional to zoom magnification. As zoom
magnification goes up, pan/tilt speed goes down.
• JOG DIRECTION [INVERSE/NORMAL]
- If you set this to ‘Inverse’, the view in the screen is
moving same direction with jog tilting. If ‘Normal’ is
selected, the view in the screen is moving
reversely.
◎ If Park Enable is set to ON, camera runs assigned
function automatically if there is no PTZ command
during assigned "Wait Time".
• PARK ENABLE [ON/OFF]
• WAIT TIME [1minute~4hour]
- The time is displayed with "hh:mm:ss" format and
you can change this by 1 min unit.
• PARK ACTION [HOME/PRESET/PATTERN/SWING/GROUP]
HOME
Camera moves to home position if there is no
PTZ command during assigned "Wait Time".
◎ Match the Alarm sensor input to one of Preset
positions. If an external sensor is activated, camera
will move to corresponding preset position when
this item is predefined.
• ALARMx TYPE [NORMAL OPEN/NORMAL CLOSE]
- Sets sensor input type.
• ALARMx ACTION [NOT USED/PRESET 1~128]
- Assign counteraction Preset position to each Alarm
input.
MOTION SETUP
PARKING ACTION SETUP
ALARM INPUT SETUP
PARKING ACTION SETUP
PARK ENABLE
WAIT TIME
PARK ACTION
BACK
EXIT
OFF
00 :10 : 00
HOME
☞
ALARM INPUT SETUP
ALARM 1 TYPE
ALARM 2 TYPE
ALARM 3 TYPE
BACK
EXIT
N. OPEN
ALARM 4 TYPE
ALARM 1 ACT
ALARM 2 ACT
ALARM 3 ACT
ALARM 4 ACT
N. OPEN
N. OPEN
N. OPEN
NOT USED
NOT USED
NOT USED
NOT USED
☞
28 29
JOG SETUP
JOG SETUP
AUTO FLIP
JOG MAX SPEED
JOG DIRECTION
BACK
EXIT
ON
120 /SEC
INVERSE
☞
CALIBRATION SETUP
CALIBRATION SETUP
CALIBRATION
BACK
EXIT
OFF ☞
MOTION SETUP
MOTION LOCK
PWR UP ACTION
FRZ IN PRESET
< PARKING ACTION SETUP >
< ALARM INPUT SETUP >
BACK
EXIT
OFF
ON
OFF
☞
< CALIBRATION SETUP >
< JOG SETUP >