CNB D2310PVF - Manual

camera color
1/3" SONY CCD
Design and specifications are
subject to change without notice.
CCD Camera Color Dome
Color Dome Digital DSP
LENS .Vari-focal
.Fixed Lens
3-Axis
•
S im
p l e
t o i n s t a l l
3 -
A x i s
b
r a
c k e t
m
ak
es ad ju st m en
t
e a
s y .
! Do not install the camera in extreme
temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 50°C.
Be especially careful with ventilation under
high temperatures.
! Do not install or use the camera in an
environment where the humidity is high.
It can cause the image quality to be poor.
! Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
! Do not disassemble the camera.
There are no user-serviceable parts inside it.
! Do not expose the camera to rain or
spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
! Note
If the camera is exposed to spotlight or
object reflecting the strong light, smear
or blooming may occur. Please check the
power whether it satisfies the normal
specification before connecting the camera.
NAME AND FUNCTION:
SPECIFICATIONS:
PRECAUTIONS:
COMPOSITION:
Model
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
(Option : AC 24V/DC 12V)
Dome Size (Ø)
Weight
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3 inch SONY IT CCD
410K/380K [Normal:270K/250K] 470K/440K[Normal:320K/290K]
More than 48dB (AGC Off)
550 TV Lines [High: 480 TV Lines / Normal: 380 TV Lines]
1.0 Vp-p (75 Ohms, composite)
Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens
Manual
Internal
0.3 Lux(High)/ 0.1 Lux(Normal)/ 0.1 Lux(Day&Night)/ 0 Lux(IR LED)
1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.
Auto
Auto, On / Off (Option)
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video, UTP (Option)
DC 12V (DC 9V~15V) / 3W (Max)
AC 24V (20V~28V) or DC 12V (10V~15V), 5W (Max)
100mm
Approx. 366g
Fixed Lens Type
CAMERA SET-UP:
Vari-focal Lens Type
INSTALLATION:
Draw out power / video wires
to the connecting places.
3
Stick the guide pattern on the
wall or ceiling.
1
Adjust desired focus and scene
by turning and moving the
3-axis camera bracket by hand.
5
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
2
Put the dome cover over the
base.
6
Fix the dome cover on the base
by covering.
7
Fixed the camera to a celling
using four screws.
4
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
P
/N
:3
8
1 0 -0
0 7 2 B
ve
r.
0 6 1 0 E
Vari-focal Lens Type
The image does not
appear on the screen.
Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.
The screen blinks a lot. Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
Built-in camera
bracket will make user
much easier to rotate in
any direction.
3-axis
360º
360º
90º
1
2
3
4
5
2
1
3
Insert coin to the side
hole and remove the
dome cover by twist coin.
NOTE
Camera Lay-out
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal
position of the screen. Focus handle: Focus (Far or Near)
Zoom handle: Zoom (Tele or Wide) 1
2
3 4
5
• The wire is non-polarized.
• Use AC 24V power source or
DC 12V power source.
CONNECTION:
• The wire is polarized.
• Use DC 12V power source.
#1
#2
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
AC24V(20V~28V)orDC12V(11V~15V), Max 5W/420mA
Terminal Color
Yellow
Green
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
DC 12V(DC9V~15V), Max 3W/ 250mA
Terminal Color
Yellow
Red
#1
#2
Video
(Yellow)
Power - DC 12V
(Red)
Video
(Yellow)
Power - AC 24V/ DC 12V
(Green)
Video Output
GND
Video Output
GND
AC 24V/DC 12V Power Type
DC 12V Power Type
Connecting to Monitor and Power
Owner's Manual
Guide Pattern
Service Monitor Cable
Mounting Screw
Dome Cover
Guide Pattern
Dome Base
Mounting
Screw
Ceiling
Simple to install
3-Axis bracket makes
adjustment easy.
The 3D bracket (Pan, Tilt and Horizontal)
allows the camera to be manually as well
as moved horizontally and vertically.
• Power Consumption: 5W
• IR LED Specification: 850nm / 30° (24EA)
IR LED (3.8mm Fixed Lens Only) : Option
CAUTION : In case of AGC off,
the switching of D&N doesn't work.
Because the D&N switching function
is related in AGC level.
DC Level Adjustment V.R a
Function Selection Switch:
•FL(Flickerless) ON/OFF
•AGC(Auto Gain Control) ON/OFF
•BLC(Back Light Compensation)
ON/OFF
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
b
c
BLC
AGC
FL
ON
OFF ON
DC
L EV EL
VI DE O
SW
IT CH ON 3
1
2
WIDE
TELE
AC 24V J503
J504
AC24V J5 01
J5 02
HE AT ER
/A UD IO
J5 05
a
b
c