Asus Barebone System Vintage-PE2 - Manual (Page 58)

4 - 6 4 - 6 4 - 6 4 - 6 4 - 6 C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
4 . 4 . 4 . 4 . 4 . C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s
( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 )
( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 ) ( 4 - p i n C P U _ F A N 1 , 3 - p i n C H A _ F A N 1 )
The fan connectors support cooling fans of 350 mA~740 mA (8.88 W
max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 before using Serial ATA hard disk drives.
®
SATA connectors
SATA1
GND
RSA
TA_TXP1
RSA
TA_TXN1
GND
RSA
TA_RXP1
RSA
TA_RXN1
GND
SATA4
GND
RSA
TA_TXP4
RSA
TA_TXN4
GND
RSA
TA_RXP4
RSA
TA_RXN4
GND
SATA3
GND
RSA
TA_TXP3
RSA
TA_TXN3
GND
RSA
TA_RXP3
RSA
TA_RXN3
GND
SATA2
GND
RSA
TA_TXP2
RSA
TA_TXN2
GND
RSA
TA_RXP2
RSA
TA_RXN2
GND
®
Fan connectors
CPU_FAN1
CHA_FAN1
GND CPU F
AN PWR
CPU F
AN IN
CPU F
AN PWM
GND
Rotation
+12V