Series 52 specifications, Pneumatic actuator & accessories, Inductive proximity sensors – Bray Pneumatic Actuators & Accessories User Manual

Page 10: As-i m12, Devicenet profibus dp

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.

The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.

Pneumatic Actuator & Accessories

Proxsensor : 10

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.

The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.

Pneumatic Actuator & Accessories

Proxsensor : 10

Series 52 Specifications

Inductive Proximity Sensors

Parameter

DC Sensor

PNP

DC Sensor

NPN

NAMUR Sensor

Intrinsically Safe

AC Sensor

Operating Voltage

10 - 30 VDC

7 - 12 VDC from IS barrier

20 - 250 VAC

Power Frequency

N/A

50 - 60 Hz

Switch Type

Inductive

Target Type

Metal (non-magnetic)

Electrical Configuration

DC - PNP - NO

DC - NPN -NO

(IS) NAMUR - NC

Maximum Load Current

200 mA DC

Limited by IS barrier

500 mA AC

Output Voltage Drop (powered)

< 2 VDC

8 VDC

< 5 VAC

Residual Current (not powered)

< 0.02 mA DC

N/A

< 1 mA AC

Output Protection

Short Circuit & Overload

N/A

None

Maximum Switching Frequency

400 Hz

10 Hz

Power Indicator

LED (green)

Uses the Position LEDs

None

Sensor Position Indicator

2 LEDs (yellow)

Housing Material

PBT VO Polymer

Protection Class

NEMA 4 / IP67

Output Connector

4-pin M12

5-pin 7/8"

Operating Temperature

-13°F (-25°C) to 158°F (70°C) -13°F (-25°C) to 158°F (70°C) -13°F (-25°C) to 158°F (70°C) -13°F (-25°C) to 158°F (70°C)

BUS Network Powered Proximity Sensors with Solenoid Drive

Parameter

AS-i Flat

Connector

AS-i M12

Connector

DeviceNet

Profibus DP

Operating Voltage

30.5 VDC AS-i Network

24 VDC DN Network

24 VDC DP Network

Consumption Current

< 30 mA DC

< 20 mA DC

< 30 mA DC

Switch Type

Hall Effect

Target Type

Magnetic

Electrical Configuration

AS-i Spec 3.2 *

DeviceNet

PROFIBUS DP

Addressing

62 Addresses

0 to 63 MAC ID

0 to 99 programmable

Data Bits

Input Bit 0: Sensor 1

Input Bit 1: Sensor 2

Output Bit 0: Solenoid Drive

Input Bit 0: Sensor 1

Input Bit 1: Sensor 2

Output Bit 0: Solenoid Drive

Input Bit 0: Sensor 1

Input Bit 1: Sensor 2

Output Bit 0: Solenoid Drive

Input Bit 0: Sensor 1

Input Bit 1: Sensor 2

Output Bit 0: Solenoid Drive

I/O and ID

I/O=3h, ID=Ah, ID2=1h

N/A

Diagnostics

Solenoid Coil Fault

Power Supply Fault

Solenoid Coil Fault

Power Supply Fault

Watchdog Timer

Solenoid Output turns Off without Network Communication

Network Indicator

Bicolor LED (red/green)

Network Communication Type Master / Slave

Master / Slave

Polled

Master / Slave

Network Comm. Connector

AS-i Flat Displacement

4-pin M12 thread

5-pin 7/8" thread

5-pin inline plug

Network Speed

N/A

125 / 250 / 500 Kbaud

Up to 1.5 Mbaud

Sensor Position Indicator

2 LEDs (yellow)

Solenoid Drive Output

24 VDC (3.6 W max.)

Solenoid Output Indicator

LED (yellow)

Solenoid Connection

3-wire PVC cable 0.7 m long, 6.0 mm diameter black, 20 AWG copper conductors

Housing Material

PBT VO Polymer

Protection Class

NEMA 4 / IP67

Operating Temperature

-13°F (-25°C) to 158°F (70°C)

-13°F (-25°C) to 158°F (70°C) -13°F (-25°C) to 158°F (70°C) -13°F (-25°C) to 158°F (70°C)

* Note: Hardware AS-i version 3.2 configured as AS-i version 2.1.
All Series 52 Valve Status Monitors are manufactured under ISO 9001 conditions.