Atec Tektronix-TDS7000B Series - Manual (Page 8)

Digital Phosphor Oscilloscopes
TDS7000B Series
Computer System and
Peripherals
CPU – TDS7104/TDS7054: Intel Celeron processor,
850 MHz.
TDS7154B/TDS7254B/TDS7404B/TDS7704B: Intel
Pentium IV processor, 2.8 GHz
*2 .
PC System Memory – 1 GB *2 .
Hard Disk Drive – 40 GB removable hard disk
drive: rear-panel or (B models only) front-panel,
(Option FHD).
Floppy Disk Drive – 1.44 MB 3.5 in. floppy disk
drive: front-panel, or (B models only) rear-panel
(Option FHD).
CD-R/W Drive – Rear-panel CD-R/W drive with CD
creation software application.
Mouse – Thumb wheel model included, USB interface.
Keyboard – Mini keyboard included (fits in pouch);
PS-2 interface. Order 119-6633-00 for full-size
keyboard; USB interface and hub.
*2 Available September 2004.
Input/Output Ports
Probe Compensator Output – Front panel BNC
connector, requires Probe Cal-Deskew Fixture
(included) for probe attachment. Amplitude 200 mV
(TDS7104/TDS7054) or 500mV (B models) ±20%
into a 50
Ω load, frequency 1 kHz ±5%.
Analog Signal Output Amplitude – Front-panel
BNC connector, provides a buffered version of the
signal that is attached to the Ch 3 input when Ch 3
is selected as trigger source. 20 mV/div ±20% into
a 1.8 M
Ω load, 10 mV/div ±20% into a 50 Ω load.
Analog Signal Output Bandwidth, Typical –
TDS7054, TDS7104: 100 MHz into a 50
Ω load.
TDS7154B/TDS7254B/TDS7404B/TDS7704B:
1 GHz into a 50
Ω load.
External Time Base Reference In – Rear-panel
BNC connector, time base system can phase-lock
to external 10 MHz reference.
Time Base Reference Out – Rear-panel BNC
connector, accepts TTL-compatible output of internal
10 MHz reference oscillator.
Auxiliary Output Levels – Front-panel BNC
connector, provides a TTL-compatible, polarity
switchable pulse when the oscilloscope triggers.
Parallel Port – IEEE 1284, DB-25 connector.
Audio Ports – Miniature phone jacks for stereo
microphone input and stereo line output.
USB Port – Allows connection or disconnection
of USB keyboard and/or mouse while oscilloscope
power is on. B models have 2 USB ports.
Keyboard Port – PS-2 compatible.
Mouse Port – PS-2 compatible.
LAN Port – RJ-45 connector, supports 10Base-T
and 100Base-T.
Serial Port – DB-9 COM1 port.
Windows Video Port – 15 pin D-Sub connector on
the rear panel; connect a second monitor to use
dual-monitor display mode. Video is DDC2B compliant.
GPIB Port – IEEE 488.2 standard.
Scope Video Port – 15 pin D-Sub connector
on the rear panel, video is IBM XGA compatible on
B models. Connect to show the oscilloscope display,
including live waveforms on an external monitor or
projector. The primary Windows desktop can also
be displayed on an external monitor using this port.
Power Source
Power – 100 to 240 V
RMS
, ±10%, 50/60 Hz;
115 V
RMS
±10%, 400 Hz; CAT II, <300 W (450 VA).
Digital Phosphor Oscilloscopes • www.tektronix.com/oscilloscopes 8