Atec Kikusui-PLZ1003W - Manual (Page 10)

Copyright © 2001 KIKUSUI ELECTRONICS CORP. All rights reserved. http://www.kikusui.co.jp/ Page10
■ Indicators
PLZ153W PLZ303W PLZ603W PLZ1003W
Ammeter
Display digits 30.00A 60.00A 99.99A 99.99A
120.0A*2 200.0A*2
Accuracy*1 ± (0.25% of FS + 1 digit) ± (0.25% of FS + 3 digits)
Temperature coefficient
±
100 ppm/
°
C of FS (typical value)
Voltmeter
Display digits 99.99V 120.0V*3
Accuracy*1 ± (0.2% of FS + 1 digit)
Temperature coefficient ± 100 ppm/ ° C of FS (typical value)
Power meter
Display digits 150.0W 300.0W 600W 1000W
Displays the results of multiplying
current value and voltage value.
*1 In a range of 23
±
5
°
C
*2 For 100 A or more, up to one digit below the decimal point will be indicated.
*3 For 100 V or more, up to one digit below the decimal point will be indicated.
■ Sub-front panel
PLZ153W PLZ303W PLZ603W PLZ1003W
Current monitoring
terminals
1 V output at rated current
Remote control 8-pin mini-connector
connector (RC11 or RC02-PLZ is connectable.)
Trigger signal output terminals
Output resistance 10 k
Ω
Output voltage 3.5 V
Pulse width Approx. 10
µ
s
■ External Control Connector
PLZ153W PLZ303W PLZ603W PLZ1003W
C.C/C.R voltage 0 A when voltage is 0 V, and rated current
control terminals*1 when 10 V (in C.C mode)
Maximum resistance when voltage is 0 V ,
and minimum resistance when 10 V (in C.R mode)
C.C/C.R resistance Rated current when resistance is about 0
Ω
,
control terminals and 0 A when about 10 k Ω (in C.C mode)
Minimum resistance when resistance is about 0
Ω
,
and maximum resistance when about 10 k Ω
(in C.R mode)
C.P voltage control
terminals
Rated power when voltage is about 10 V
Load-on/off monitoring Photo coupler (open collector)
output terminals Rated voltage: 30 V
(floating output) Rated current: 5 mA
Load-on/off signal Comparator level: about 7 V
input terminal 3.3 k
Ω
is pulled up with 15 V.
Range selector signal
input terminals
CMOS level 10 k Ω is pulled up with 5 V.
Trigger signal output terminals (floating output)
Output resistance 10 k Ω
Output voltage 3.5 V
Pulse width Approx. 10 µ s
Trigger input terminals CMOS level Pull down at 100 k Ω
Current monitoring
terminals (output of Rated current/1 V
a sum of currents)
Short-circuit signal
output
Relay contact output (25 V DC, 0.5 A)
*1 In full scale, and offset adjustable
■ Others
PLZ153W PLZ303W PLZ603W PLZ1003W
Input power supply (AC)
Input supply voltage
range (AC)
Frequency 50/60 Hz AC
Power consumption (VA)
(When the GPIB board
Approx. 50 Approx. 55 Approx. 70 Approx. 110
is connected)
(60) (65) (80) (120)
Rush current (A) Approx. 18 Approx. 22 Approx. 28 Approx. 32
Withstand voltage
Primary circuit to
load terminals
1500 V AC for 1 min
Primary circuit to
chassis
1500 V AC for 1 min
Insulation resistance
Primary circuit to
load terminals
500 V DC, 30
ΜΩ
or more
Primary circuit to
chassis
500 V DC, 30
ΜΩ
or more
Load terminals to
chassis
500 V DC, 20 ΜΩ or more
Operating temperature
range
0 to 40 ° C
Operating humidity
range
30 to 80% RH (no condensation)
Storage temperature
range
-20 to 70 ° C
Storage humidity range 30 to 80% RH (no condensation)
Weight (kg) Approx. 8.5 Approx. 10 Approx. 16 Approx. 19.5
PLZ-3W/3WH series
ELECTRONIC LOAD (CC·CR·CV·CP)
1.5V
0
3
2
1
0.1
0
1 0.20 0.1 0.05 0.025 0.01
4.5
5
4
3.5
3
2.5
2
1.5
1
0
1.5 3 5 10 15 20 120
1000W
600W
300W
150W
60W
Current ripple P-P(A)
Graph 1 Setting Resistance and Current Ripple
Setting resistance( Ω )
Current ripple P-P(A)
Graph 2 Setting Power and Current Ripple
Input voltage(V)
Rated voltage
(120V)
Input voltage
Graph 3 Operationg Range
Rated power
Input current Rated current
Range Center voltage
[1] 90 to110 100
[2] 108 to132 120
[3] 180 to220 200
[4] 216 to250 240
[1], [2], [3], or [4] is selectable.