Atec Fluke-Norma-4000-5000 Series - Manual (Page 8)

8
Voltage
8 ranges:
0.3 – 1 – 3 – 10 – 30 – 100 – 300 –
1000 V
U
peak
= 2 x range
Input impedance: 2 MOhm / 20 pF
CMR common mode rejection: 120 dB at 100 kHz
PP54 Power Phase
Ranges
ENEN
Fluke Corporation Fluke Norma 4000/5000 power analyzers
Current
6 ranges:
30 – 100 mA – 0,3 – 1 – 3 – 10 A
I
peak
= 2 x range; max level 150% at
sine wave (limit of error as at 100%).
Input impedance with integrated shunts:
Ranges
30, 100 mA: 1 Ohm
Ranges 0.3, 1 A: 0.1 Ohm
Ranges 3, 10 A: 0.01 Ohm
Current overload: max. 15 A continuous
30 A < 5 sec / 15 sec no load
100 A < 0.1 s / 30 sec no load
Input for external shunt or probe:
BNC terminal:
100 kOhm / 30 pF
30 – 100 mV – 0.3 – 1 – 3- 10 V
Overload: max. 20 V
rms
CMR common mode rejection: 120 dB at 100 kHz
Error of Amplitude
Basic accuracy PP54
Sum limit of error
U I
range 0.05% 0.05%
reading 0.05% 0.05%
Voltage and current depending on the input
level at 45 – 65 Hz frequency range
Input level Sum limit of error U Sum limit of error I
in % in % in %
100 0.10 0.10
50 0.15 0.15
30 0.22 0.22
10 0.55 0.55
5 1.05 1.05
3 1.72 1.72
1 5.05 5.05
PP54 Bandwidth
U and I via BNC I direct measured
Bandwidth –3 dB 3 MHz 1 MHz
Current measurement accuracy
depending on the frequency (reading + range)
Frequency Limits of error current [ % ]
[Hz] Internal shunt [Hz]
0 0.10 -0.10 0.10 -0.10
10 0.10 -0.10 0.10 -0.10
45 0.10 -0.10 0.10 -0.10
65 0.10 -0.10 0.10 -0.10
500 0.10 -0.10 0.10 -0.10
1000 0.10 -0.10 0.10 -0.10
2000 0.15 -0.28 0.13 -0.22
5000 0.20 -0.52 0.17 -0.38
10000 0.25 -0.70 0.20 -0.50
20000 0.30 -0.88 0.23 -0.62
50000 0.35 -1.12 0.27 -0.78
100000 0.40 -1.30 0.30 -0.90
Voltage measurement accuracy depending on
the frequency (reading + range)
Frequency in Hz Limits of error voltage in %
0 0.10 -0.10
10 0.10 -0.10
45 0.10 -0.10
65 0.10 -0.10
500 0.10 -0.10
1000 0.10 -0.10
2000 0.13 -0.22
5000 0.17 -0.38
10000 0.20 -0.50
20000 0.23 -0.62
50000 0.27 -0.78
100000 0.30 -0.90
Valid for averaged values at 23 ± 0.5 °C ambient
temperature, sine waveform and after 1 hour turn on time
with measuring signal.
Power / Angular Error
PP54 Between U and I
BNC
Between U and I
Shunt
Angular Error 0.005° +0.005° / kHz 0.025° + 0.015° / kHz
Aliasing filter OFF
Error Power
Frequency in Hz Limit of error power in % at Lamda = 1
45 0.16 -0.16
65 0.16 -0.16
Voltage
8 ranges:
0.3 – 1 – 3 – 10 – 30 – 100 – 300 –
1000 V
U
peak
= 2 x range
Input impedance: 2 MOhm / 20 pF
CMR common mode rejection: 120 dB at 100 kHz
PP64 Power Phase
Ranges