Atec Fluke-Norma-4000-5000 Series - Manual (Page 7)

ENEN
7 Fluke Corporation Fluke Norma 4000/5000 power analyzers
Error Power
Frequency in Hz Limit of error power in % at Lamda = 1
45 0.33 -0.33
65 0.33 -0.33
PP50 Power Phase
Ranges
Voltage
8 ranges:
0.3 – 1 – 3 – 10 – 30 – 100 – 300 –
1000 V
U
peak
= 2 x range
Input impedance: 2 MOhm / 20 pF
CMR common mode rejection: 120 dB at 100 kHz
Current
6 ranges:
30 – 100 mA – 0.3 – 1 – 3 – 10 A
I
peak
= 2 x range; max level 150% at
sine wave (limit of error as at 100%).
Input impedance with integrated shunts:
Ranges 30, 100 mA:
1 Ohm
Ranges 0.3, 1 A: 0.1 Ohm
Ranges 3, 10 A: 0.01 Ohm
Current overload: max. 15 A continuous
30 A < 5 sec / 15 sec no load
100 A < 0.1 s / 30 sec no load
Input for external shunt or probe:
BNC terminal:
100 kOhm / 30 pF
30 – 100 mV – 0.3 – 1 – 3- 10 V
Overload: max. 20 Vrms
CMR common mode rejection: 120 dB at 100 kHz
Error of Amplitude
Basic accuracy PP50
Sum limit of error
U I
range 0.05% 0.05%
reading 0.05% 0.05%
Voltage and current depending on the input
level at 45 – 65 Hz frequency range
Input level Sum limit of error U Sum limit of error I
in % in % in %
100 0.10 0.10
50 0.15 0.15
30 0.22 0.22
10 0.55 0.55
5 1.05 1.05
3 1.72 1.72
1 5.05 5.05
PP50 Bandwidth
U and I via BNC I direct measured
Bandwidth –3 dB 10 MHz 1 MHz
Current measurement accuracy
depending on the frequency (reading + range)
Frequency Limits of error current [ % ]
[Hz] Internal shunt BNC input
0 0.10 -0.10 0.10 -0.10
10 0.10 -0.10 0.10 -0.10
45 0.10 -0.10 0.10 -0.10
65 0.10 -0.10 0.10 -0.10
500 0.10 -0.10 0.10 -0.10
1000 0.10 -0.10 0.10 -0.10
2000 0.12 -0.19 0.12 -0.16
5000 0.15 -0.31 0.13 -0.24
10000 0.18 -0.40 0.15 -0.30
20000 0.20 -0.49 0.17 -0.36
50000 0.23 -0.61 0.18 -0.44
100000 0.25 -0.70 0.20 -0.50
Voltage measurement accuracy depending on
the frequency (reading + range)
Frequency in Hz Limits of error voltage in %
0 0.10 -0.10
10 0.10 -0.10
45 0.10 -0.10
65 0.10 -0.10
500 0.10 -0.10
1000 0.10 -0.10
2000 0.12 -0.16
5000 0.13 -0.24
10000 0.15 -0.30
20000 0.17 -0.36
50000 0.18 -0.44
100000 0.20 -0.50
Valid for averaged values at 23 ± 0.5 °C ambient
temperature, sine waveform and after 1 hour turn on time
with measuring signal.
Power / Angular Error
PP50 Between U and I
BNC
Between U and I
Shunt
Angular Error 0.005° +0.005° / kHz 0.025° +0.015° / kHz
Aliasing filter OFF
Error Power
Frequency in Hz Limit of error power in % at Lamda = 1
45 0.16 -0.16
65 0.16 -0.16
Voltage measurement accuracy depending on
the frequency (reading + range)
Frequency in Hz Limits of error voltage in %
0 0.20 -0.20
10 0.20 -0.20
45 0.20 -0.20
65 0.20 -0.20
500 0.20 -0.20
1000 0.20 -0.20
2000 0.23 -0.32
5000 0.27 -0.48
10000 0.30 -0.60
20000 0.33 -0.72
50000 0.37 -0.88
100000 0.40 -1.00
Valid for averaged values at 23 ± 0,5 °C ambient temperature,
sine waveform and after 1 hour turn on time with measuring
signal.
Power / Angular Error
PP42 Between U and I
BNC
Between U and I
Shunt
Angular Error 0.005° +0.005° / kHz 0.025° +0.015° / kHz
Aliasing filter OFF