Atec Mitutoyo-SJ-410 - Manual (Page 9)

9
For deep groove (10mm)
12AAC735 (2μm) * 1
12AAB409 (5μm)
12AAB421 (10μm)
( ): Tip radius
For deep groove * 2 (20mm)
12AAE893 (2μm) * 1
12AAE909 (5μm)
( ): Tip radius
For deep groove * 2 (20mm)
12AAC736 (2μm) * 1
12AAB408 (5μm)
12AAB420 (10μm)
( ): Tip radius
For deep groove * 2
(40mm)
12AAE895 (2μm) * 1
12AAE911 (5μm)
( ): Tip radius
For deep groove * 2 (30mm)
12AAC737 (2μm) * 1
12AAB407 (5μm)
12AAB419 (10μm)
( ): Tip radius
For deep groove (30mm) / Double-length for deep hole * 2
12AAE894 (2μm) * 1
12AAE910 (5μm)
( ): Tip radius
For gear tooth
12AAB339 (2μm) * 1
12AAB410 (5μm)
12AAB422 (10μm)
( ): Tip radius
For gear tooth / Double-length for deep hole * 2
12AAE896 (2μm) * 1
12AAE912 (5μm) * 1
( ): Tip radius
For rolling circle waviness surface * 4
12AAB338 ( φ1.588)
( ): Tip radius
For rolling circle waviness / Double-length for deep hole * 2 * 4
12AAE886 (250μm)
( ): Tip radius
For knife-edge * 4
12AAC738 (2μm) * 1
12AAB411 (5μm)
12AAB423 (10μm)
( ): Tip radius
For corner hole / Double-length for deep hole * 2
12AAE897 (2μm) * 1
12AAE913 (5μm) * 2
( ): Tip radius
For eccentric arm * 2
12AAC739 (2μm) * 1
12AAB412 (5μm)
12AAB424 (10μm)
( ): Tip radius
For hole bottom
12AAE899 (2μm) * 1
12AAE915 (5μm)
( ): Tip radius
*1: Tip angle 60°
*2: For downward-facing measurement only.
❈
Customized special interchageable styli are available on request,
Please contact any Mitutoyo office for more information.
90 °
13
φ
2.4
0.9
φ 1.2
14.2
37.7
44.7
A
Color
coding* 3
Detail-A
深溝用（ 10mm ）
23
0.9
φ
2.4
24.2
φ 1.2
90 °
37.7
44.7
A
識別色
A 部詳細
Color
coding* 3
Detail-A 90 °
23 φ
2.4
φ1.2
24.2
37.7
44.7
A
深溝用（ 20mm ）
33
31.8
5.2
φ 1.2
A
φ 2.4
φ
2.4
90 °
37.7
45.2
Color
coding* 3
Detail-A
深溝用（ 30mm ）
60
°
60
°
7.6
6.4
37.7
43.8
φ
1.2 φ
2.4
A
Color
coding* 3
Detail-A
歯面用
7.6
φ
2.4
φ 1.2
0.9 37.7
44.7
Ball φ 1.588
5.2
転がり円
うねり用
7.6
φ
2.4 φ 1.2
90 °
37.7 0.9
44.7
A
Color
coding* 3
Detail-A
ナイフエッジ用
A
37.7 0.9
90 °
φ 1.2
45.2
7.6
10
φ
2.4
φ
2.4
識別色
A 部詳細
Color
coding* 3
Detail-A
心違い用
90 °
φ
2.4 φ 1.2
45.2
1.4 37.7
7.6
φ
2.4 10
A
*3 : Tip radius 2μm 5μm 10μm
Color coding Black No color Yellow
*4 : Used for calibration, a standard step gauge (No.178-611, option) is also required
23
21.8
5.2
95.2
87.7
φ 2.4
φ 1.2
深溝用 2 倍（ 20mm ）
43.8 42.6
5.2
φ
2.4
45.2
37.7
φ 2.4
φ 1.2
深溝用（ 40mm ）
36.5 35
5.2
φ
3
93.8
87.7
φ 1.2
深溝用（ 30mm ）
深穴 2 倍
36.5 35
φ
3
93.8
6.77
87.7
φ 1.2
60
°
歯面用
深穴 2 倍
94.7
0.9 87.7
φ 1.2 φ
2.4
5.2 6.4 7.6
転がり円うねり・深穴 2 倍
93.8
87.7
35
φ
0.8
45
°
5.8 5 φ
1.6
φ
2.4
穴測定コーナー用・深穴 2 倍
穴底用
7.4
φ
1
0.5
5 6.2
φ
2.4
44.3
37.7
Styli
Unit: mm