Atec Agilent-N4010A - Manual (Page 12)

12
N4010A vector signal analyzer specifications
When used with 89601A/89607A (requires Option 110 and at
least one of Option 101, 102, or 103). For the full N4010A/89601A
performance guide refer to application note Agilent N4010A
Wireless Connectivity Test Set Performance Guide Using the
89601A Vector Signal Analysis Software and the 89607A WLAN
Test Suite Software, literature number 5989-0637EN.
Performance
Sampling frequency 100 MHz digital down-conversion
Quantization 14 bits
Sampling resolution 10 ns
Acquisition buffer 5 ms
Frequency specifications
Frequency range 1 2.381 to 2.519 GHz
4.800 to 5.875 GHz (Option 103 only)
Frequency resolution 1 MHz
Frequency accuracy 2 As frequency reference ±100 Hz
IF bandwidth Switchable between 22 and 40 MHz
Stability (noise sidebands)
offset
10 kHz: < –75 dBc/Hz (nominal)
100 kHz: < –95 dBc/Hz (nominal)
Amplitude specifications
Power measurement
range
+23 to –70 dBm (2.381 to 2.519 GHz)
+23 to –50 dBm (4.800 to 5.875 GHz)
Maximum safe
input level
+25 dBm
Absolute power
measurement
accuracy 2
±0.5 dB 3 (2.381 to 2.519 GHz)
±0.3 dB 4 (+23 to –55 dBm)
±0.35 dB 4 (< –55 dBm)
±0.8 dB 3 (4.800 to 5.875 GHz)
±0.35 dB 4 (+23 to –55 dBm)
RF input VSWR < 1.5:1 (return loss: > 14 dB)
(2.381 to 2.519 GHz)
< 1.8:1 (return loss: > 10 dB)
(4.800 to 5.875 GHz)
Signal-to-noise
ratio 5, 6
> 52 dB for 22 MHz bandwidth
(2.381 to 2.519 GHz)
> 45 dB for 22 MHz bandwidth
(4.800 to 5.875 GHz)
Spurious responses < –90 dBm (2.381 to 2.519 GHz)
In-band spurious 7 < –60 dBm (4.800 to 5.875 GHz)
Trigger ranges
Internal trigger
power
–60 to +23 dBm for 22 MHz bandwidth; –65
to +23 dBm for 5 MHz bandwidth (2.381 to
2.519 GHz) –65 to 0 dBm for 22 MHz band-
width (4.800 to 5.875 GHz)
External trigger
voltage
3.3 V (TTL)
Trigger delay range –4.5 to 5.2 ms, or time capture length,
whichever is shorter (see performance
guide 5989-0637EN)
Trigger hold-off
range
20 ns to 0.65 ms
Modulation specifications
Residual error
vector magnitude
(EVM)
802.11a: 5 GHz band; 54 Mbps 64QAM OFDM:
< 2.25% (power range 0 to –20 dBm)
802.11b: DSSS: < 3.0% (power range 0 to
–30 dBm)
802.11g: 2.4 GHz band; 54 Mbps 64QAM
OFDM: < 1.25% 8 (power range 0 to –30 dBm)
802.11g: 2.4 GHz band; 54 Mbps 64QAM
OFDM: < 2.5% (power range +5 to 0 dBm)
802.11n: 54 Mbps 64QAM OFDM:
< 1.75% 9 (power range 0 to –10 dBm)
802.11n: 54 Mbps 64QAM OFDM:
< 3.0% 9 (power range –10 to –20 dBm)
Bluetooth EDR: < 2% (rms DEVM)
1. This is the center frequency tuning range for a 22 MHz span. With a 40 MHz
span, the frequency ranges are 2.39 to 2.51 GHz and 4.809 to 5.866 GHz.
2. Verified using CW measurements.
3. Add 0.02 dB/°C from 30 to 55 °C, add 0.025 dB/°C from 20 to 0 °C.
4. Typical specification applies to instruments serial number GB4617 or
greater, or instruments with the serial number starting MY.
5. 0 dBm input.
6. Specification applies to instruments serial number GB45460101 or
greater, otherwise this specification for the 2.4 GHz band is > 46 dB
(22 MHz bandwidth),
7. > 50 dB (5 MHz bandwidth).
8. Specification applies to instruments serial number GB45460101 or
greater, otherwise this specification is < –70 dBm (2.381 to 2.519 GHz).
9. Typical specification applies to instruments serial number GB4617 or
greater, or instruments with the serial number starting MY; otherwise the
specification is < 2.0%.
10. Specification applies to instruments with Option 108.