Astro Pneumatic 3025 6 Finishing Palm Sander - 3/32 Stroke Finish - Manual (Page 3)

Page 3
8) Slip/Trip/Fall is a major reason of serious injury or death.
Beware of excess hose left on the walking or work surface.
9) Wearing eye/face protector could reduce the danger to
person from high speed splinters being emitted from the
tool or work surface.
10) Wearing correct breathing protection will help avoid
inhaling dust or handling debris form work process that
can be harmful to your health.
12) High sound level can cause permanent hearing loss.
Use hearing protection while operating tool.
13) Due to the material being processed, there may be a
risk of explosion or fire. Be aware of work suface dangers
prior to begining work.
14) There is a risk of being cut due to high speed
rotation. Do not touch high speed rotating disc.
15) This power tool is not insulated. If contact is made with
an electric current injury may occur.
16) Dust created by sanding, sawing, grinding, drilling and
other related activities may expose the user to dust and/or
microscopic particles that may contain chemicals known to
the State of California to cause cancer, birth defects or
other reproductive harm.
Users of this tool should review the chemical composition
of the work surface and any products used in conjunction
with the operation of this tool for any such chemicals prior
to engaging in any activity that creates dust and/or
microscopic particles.
Users should obtain the Material Safety Data Sheets for all
identified chemicals, either from the manufacturer or their
employer, and proceed to study, understand, and follow all
instructions and warnings for exposure to such chemicals.
Some examples of these chemicals are: lead from lead-
based paints; crystalline silica from bricks, cement and
other masonry products; and arsenic and chromium from
chemically treated lumber. A listing of the chemicals can
be obtained from www.oehha.ca.gov under Proposition 65.
In order to reduce their exposure to such chemicals, users
should always:
*
work in well-ventilated areas.
*
wear appropriate safety equipment and clothing that are
specifically designed to filter out microscopic particles.
Maintenance instruction:
1)Lubrication:
Before connecting the hose, apply 4 to 5 drops of
#60 spindle oil at the air inlet. After 3 to 4 hours
of operation, oiling may be necessary again.
2)Tightness of parts:
Regularly check whether all connecting parts are
fastened securely. Follow this procedure daily
before beginning work.
3)Cleanness:
Dust may accumulate around spindle inside
shield. It is recommended to remove
the dust on daily basis.
4)Storage:
Avoid storing the tool in a location subject to high
humidity. If the tool is left unused, the residual
moisture inside the tool can cause rust. Before
storing and after operation, oil the tool at the air
inlet with spindle oil and run it for a short period.
5)Disposal:
Follow national legislation of Waste disposal. Never
drop into fire.
6)Ordering service part:
For further operational and handling information or
for replacement of parts and components, contact the
sales agent from whereyou purchased the tool, or the
service division of our company.
* In ordering parts and components, give each part
number, name and quantities.
1) The tool shall not be used in potentially explosive
atmospheres.
2) Disconnect the air hose before changing or
adjusting any inserted tools.
3) Before using tool, please confirm all couplings
and plugs are fixed securely. Air hose that is under
pressure may lash out when disconnected
and could lead to serious injuries.
4) Prevent loose clothes, long hair or any other
personal accessories from coming close to moving
parts to reduce the risk of being caught, trapped
or drawn into the rotating spindle.
5) Excessive high air pressure, that exceeds the
maximum pressure, may cause injuries to user.
6) Exposure to strong vibration for extended time
may cause harm to operator.
7) Make sure of the rotation direction before starting
the tool to reduce hazardous situations due to
unexpected rotation direction.
Cautions for Use
1) Always wear ear protection and safety glasses when using
this tool. Gloves and protective clothing are recommended.
2) Personal protection and dust collection devices shall be
chosen according to the material being worked upon. Please
consult provider of such devices.
3) Release the start and stop device incase of failure of energy
supply.
4) Never use hand sockets. Only use power drive sockets.
5) Basic safety instructions and warnings must always be
followed. in addition, safety instructions & warnings identified
in ANSI B186.1 Safety Code for Portable Air Tools must be
followed. For further ANSI information see www.ansi.org or
call (212) 642-4900
3025
6“ Finishing Palm Sander