beautypg.com

Astro Pneumatic 1869 1 Heavy Duty Air Impact Wrench with 6 Anvil User Manual

Product information, 1" heavy duty air impact wrench with 6" anvil, Important

background image

1869

1869

1" HEAVY DUTY AIR IMPACT WRENCH

with 6" Anvil

1" HEAVY DUTY AIR IMPACT WRENCH
with 6" Anvil

2

Important

1868-1
1868-2
1868-3

1868-4
1868-5
1868-6

1868-7
1868-8
1868-9
1868-10

1868-11
1868-12

1868-13

1868-14
1868-15
1868-18

1868-19

1868-20

1868-21
1868-22

1868-23

1868-24
1868-25

Product Information:

When unpacking, check the parts diagram and part number
listing on page 2 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.

Unpacking

www.astrotools.com

Always wear ANSI approved safety goggles when using this product.
Normal use of this product is likely to expose the user to dust and/or
microscopic particles containing chemicals known to the Sate of
California to cause caner, birth defects or other reproductive harm.
Always wear appropriate safety equipment and clothing when using
this product. Study, understand, and follow all instructions provided
with this product.

1

1

1

1

1

1

1

1

1

1

1

1

1

1

3

1

1

1

1

1

8

8

1

1

Trigger Handle Assembly

Plunger Bushing

Reverse Valve Bushing

Inside Trigger

Pin

Spring Pin

Slot Cover

Throttle Valve

Throttle Valve Plunger

Throttle Valve Spring

Angle Inlet Bushing

Reverse Valve Knob

Ball

Protective Rubber Boot

O-Ring

Spring Pin

Spring Pin

Spring

Spring Pin

Handle Gasket

Handle Cap Screw

Lock Washer

Motor Housing

Bearing

1868-26

1868-27
1868-28

1868-29
1868-30
1868-31

1868-32
1868-33
1868-34
1868-35

1868-36
1868-37

1868-38

1869-39
1868-40
1868-41

1868-43

1868-44
1868-45

1868-46
1868-47

1868-48
1868-49
1868-50
1868-51

1

1

1

6

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

4

1

1

1

Rear End Plate Assembly

Spring Pin

Rotor

Vane

Cylinder Assembly

Spring Pin

Front End Plate

Bearing

Hammer Frame

Hammer Cam

Hammer

Side Plate

6” Anvil

Screw

Retainer Ring

Hammer Case Assembly

Hammer Case Bushing

Oil Seal

Protective Rubber Boot

Hammer Case Gasket

Dead Handle Cap Screw

Handle Grip

Swept Back Handle

Screw Lock Washer

Normal use of this product is likely to expose
the user to dust and/or microscopic particles
containing chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm. Always wear
appropriate safety equipment and clothing when
using this product. Study, understand and follow
all instructions provided with this product.
Always wear ANSI approved goggles when using
this product.
Always select the correct accessories of the
correct size and design for the job that you are
attempting to perform.
Always work in a clean, safe, well-lit, organized
and adequately equipped area.
Do not begin repairs without assurance that

vehicle is in secure position, and will not move

during repair.

• Ideal for tire work on trucks, buses and off-road, farm equipment
• "Pin-less" impact mechanism submits brute force strike
with low vibration
• 6" anvil makes tool perfect for the demanding world
of truck tire service
• Six-position power management/regulator
(3 forward & 3 reverse)
• Air Inlet with 45 degree angle
• Air Exhaust - Upward (away from work piece)
• Swept-back side handle & protective rubber boot

SPECIFICATIONS

Working Torque Range:

300-1400 ft/lbs (408-1904 NM)

Max. Torque:

1800ft/lbs (2448NM)

Blow per minute:

750

Free Speed:

5000rpm

Recommended Air Pressure:

90psi (6.35kgs)

Air Inlet:

1/2" NPT

Minimum Hose Size:

1/2" I.D.

Overall Length:

20.1" (510mm)

Weight:

27lbs (12.3kgs)

(B)

01/9/2006

Table of contents