Astro Pneumatic 78241 Wheel Bearing Replacement Adapter Set - Manual

Page 1
IMPORTANT
www.astrotools.com
PLEASE CALL 1-800-221-9705
FOR REPAIR AND RETURN INSTRUCTIONS
Read these instructions carefully before
installing, operating, servicing or repairing this
tool. Keep these instructions in a safe
accessible place.
Model:
Foreseen Use of the Tool
This set is designed to change front wheel bearings on front wheel
drive cars and light trucks. Do not use this tool outside of the
designed intent. Never modify the tool for any other purpose or use.
Safety Precaution
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
Caution: To help prevent personal injury
PRODUCT INFORMATION
SPECIFICATIONS
When unpacking, check the parts diagram and part number
listing on page 6 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year from the date of 1st use.
Astro reserves the right to determine whether the product failed because of defective
material, workmanship or other causes and to charge back for missing parts. Astro
Pneumatic Tool Co., at its discretion, will repair products covered under this warranty
free of charge. The original user is to return the product (with the exceptions listed
below) with the distributor’s name, address, adequate proof of date of purchase or a
copy of warranty card, and a short note explaining the problem. Failures caused
by accident, alteration, or misuse are not covered by this warranty.
•
If one part of this product fails, please do not return the entire product.
Astro will replace free of charge component parts of this product that fail
within 1 year of first use by the original user. Items included in this category
include but are not limited to kits, hand tool kits and any other product where
there are multiple items or components that make up the unit. Please contact
the phone number below in order to obtain the replacement components
covered under warranty.
•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user
and may not be transferred to subsequent owners.
•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
372 Old US Highway 52 South
Mt. Airy, NC 27030
1 YEAR LIMITED WARRANTY
Product Type:
• Construction : Low Carbon Steel
• Finish : Black Oxide
• Bushing Hardness : HRC25 to HRC35
• Bushing Range (Outside Diameter) : 2.17", 2.49", 2.62", 2.76", 2.81",
2.32", 2.87", 2.94", 2.91", 3.05",
3.21", 3.29", 3.46"
• Sleeve Sizes :
2.99" O.D. X 2.56" Long, 3.39" O.D. X 2.56" Long
3.58" O.D. X 2.56" Long, 4.02" O.D. X 2.56" Long
• Sleeve Plate Sizes :
3.39" O.D. X 0.71" Step, 4.02" O.D. X 0.70" Step
• Sliding Screw Size/Type : 8.23" Long X 0.75" Diameter / 16 NAT
• Nut Size : 2.66" Long x 0.75" Diameter
• Washer Sizer : 2.01" O.D.
• Change front wheel bearings without the hassle of
removing steering knuckle or strut assembly
• Eliminates the need for front end alignment after service
work is completed
• For use with both domestic and import front wheel drive
cars and light trucks
• Corrosion resistant black oxide finish
78241
WHEEL BEARING REPLACEMENT
ADAPTER SET