beautypg.com

Astro Pneumatic 8077SE User Manual

Revised not printed yet, Outside inside, 8077se

background image

Product: 8077SE Manual
Dimension: 8.5"x 11"/page
Date: 2009/08/27

Color:

Black

outside

inside

fig.2

fig.1

'T'

ASSEMBLY & OPERATION

The helmet comes ready assembled but before it can be used

it must be adjusted to fit the user properly and set up for

delay time,sensitivity and shade level.

ADJUSTING THE FIT OF THE HELMET

• The overall circumference of the headband can be made larger

or smaller by rotating the knob on the back of the headband.

(See adjustment "Y" in fig.1) This can be done whilst wearing the

helmet and allows just the right tension to be set to keep the

helmet firmly on the head without it being too tight.

• If the headband is riding too high or too low on your head adjust

the strap which passes over the top of your head. To do this

release the end of the band by pushing the locking pip out of the

hole in the band. Slide the two portions of the band to a greater

or lesser width as required and push the locking pip through the

nearest hole (See adjustment "W" in fig.1)

• Test the fit of the headband by lifting up and closing down the

helmet a few times while wearing it. If the headband moves while

tilting re-adjust it until it is stable.

ADJUSTING DISTANCE BETWEEN HELMET & FACE

• Step 1: Undo the block nut (See "T" in fig.1) to adjust the

distance between the helmet and your face in the

down position.
• Step 2: loosen the block nut on either side of the helmet and

slide it nearer to or further from your face.

(See adjustment "Z" in fig.1) It is important that your eyes

are each the same distance from the lens otherwise the

darkening effect may appear uneven.

• Step 3: Re-tighten the block nut when adjustment is complete.

ADJUSTING ANGLE OF THE MASK IN THE DOWN POSITION

• If the lens is not properly aligned with the eyes in the down

position the mask angle can be further adjusted into one of three

preset positions using the tilt plate shown in fig.2. Behind each

pivot knob on the sides of the helmet there is a screw which

passes through the side of the mask and into one of the holes in

the tilt plate ( see A,B,C in fig.2 ).

• Partially undo each screw counterclockwise so that it withdraws

out of the tilt plate but remains in the side of the mask. Rotate the

assembly so that one of the alternative positions is aligned with

the end of the screw. Turn the screws clockwise again so that

they pass through the holes thus fixing the position of the tilt

plate.

SELECTING SHADE LEVEL

• Select the shade level you require according to the welding

process you will use by referring to the "Shade Guide Table"

below for settings. Turn the shade control knob on the side of the

helmet to the shade number required.

SELECTING DELAY TIME

• When welding ceases the viewing window automatically

changes from dark back to light but with a pre-set delay to

compensate for any bright afterglow on the workpiece. The delay

time/response can be set to "short" to "long" as you require

using the dial knob on the back of the shade cartridge. (See fig.3)

SENSITIVITY

• The sensitivity can be set from "high" to "low" using the dial

knob on the back of the shade cartridge. The"low" setting is the

normal setting for everyday use.

• Where the operation of the mask is disturbed by excess

ambient light or another welding machine close by, use the "low"

setting. (See fig.3).

• Please adjust the sensitivity to the lowest level when you are

not working.

You are now ready to use the helmet, The shading may be

adjusted during use by re-setting potentiometer control.

fig.3

Sever personal injury could occur if the user fails to follow the

above mentioned warnings, and/or fails to follow the operating

instructions.

fig.4a

fig.4

3

Before using the helmet for welding ensure you

have read and understood the safety instructions

MAINTENANCE INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Viewing Area: 96 x 62 mm (3.8"x2.4")
Cartridge Size: 110 x 106 x 9mm (4.3"x4.2"x0.35")
Arc Sensor: 2
Light State: Shade DIN 3.5
Variable Shade: From DIN 9 to DIN 13
Shade Control: External adjustable
Power On/Off: Fully Automatic
Sensitivity Control: Be adjustable by dial knob
UV/IR Protection: Up To Shade DIN16 at all time
Power Supply: Solar cell, battery can be changed (3V lithium)
Battery Lifetime: Over 4000hours before low battery alarming
Switching Time: 1/20,000 s. from Light to Dark
Dark to Light: 0.1~1.0s by dial control knob
Operating Tep.:

- 1 0

。 C ~ + 55。C

Storing Temperature: - 20

。 C ~ + 70。C

Helmet Material: High-impact resistant plastic /
Polyamide Nylon
Total Weight: 475g

COMMON PROBLEMS AND REMEDIES

• REPLACING FRONT COVER LENS. Replacing the front

cover lens if it is damaged (cracked, scratched, soiled or pitted).

See fig.4

• CHANGING BATTERY. If "Low battery" alarm light is red,

please change it with new battery.

• CLEANING. Clean helmet by wiping with a soft cloth. Clean

cartridge surfaces regularly. Do not use strong cleaning solutions.

Clean sensors and solar cells with methylated spirit and a clean

cloth and wipe dry with a lint-free cloth.

PLEASE ADJUST THE SENSITIVITY TO THE LOWEST

LEVEL WHEN YOU ARE NOT WORKING.

Irregular Darkening Dimming

• Headband has been set unevenly and there is an uneven
distance from the eyes to the filter's lens (Reset headband to
reduce the difference to filter).

Auto-Darkening Filter Does Not Darken Or Flickers

• Front cover lens is soiled or damaged (change lens cover)

• Sensors are soiled (clean the sensors' surface)

• Welding current is too low (turns the switch to the "slow"
position).

Slow Response

• Operating temperature is too low (do not use at temperatures
below - 10

。C or 14。F).

Poor Vision

• Front /inside cover lens and/or filter lens are soiled
(change lens)
• There is insufficient ambient light

• Shade number is incorrectly set (reset the shade number)

Welding Helmet Slips

• Headband is not adjusted properly (readjust headband)

User must stop using the auto-darking welding helmel

immediately if the above-mentioned problems cannot

be corrected. Contact Astro Pneumatic Tool Company.

sensitivity

delay time

1

2

3

4

14

5

6

7

8

9

10

15

11

12

13

Call 1.800.221.9705 for questions concerning performance of the product

or other inquiries.

8077SE

372 Old US Highway 52 South

Mount Airy, NC 27030

LARGE VIEWING AREA DELUXE

AUTO-DARKENING SOLAR WELDING

HELMET AND WELDING GLOVES

8077-01
8077-02
8077-03
8077-04
8077-05
8077-06
8077-07
8077-08

Frame
Front Cover Lens
Shade Knob
Auto-Darkening Filter Cartirdge
Shell (Welding Mask)
Block Nut
Washer
Adjustable Limitation Washer

1
1
1
1
1
2
4
2

1
2
6
4
5
6
7
8

Index

No.

8077-09
8077-10
8077-11
8077-12
8077-13
8077-14
8077-15

Left Limitation Washer
Screw
Right Limitation Washer
Front Headband
Adjustable Headband
Inside Cover Lens
Sweatband

1
2
1
1
1
1
1

9

10
11
12
13
14
15

Index

No.

REVISED NOT PRINTED YET

1

4

PRODUCT INFORMATION

Caution: To help prevent personal injury

Safety Precaution

Foreseen Use of the Tool

Do not use the tool outside of the design intent.

Never modify the tool for any other purpose, or for its use.

Model:

Product Type:

www.astrotools.com

Auto-Darkening Welding Helmets are designed to protect the eye and

face from sparks, spatter, and harmful radiation under normal welding

conditions. Auto-darkening filter automatically changes from a light

state to a dark state when an arc is struck, and it returns to the light

state when welding stops.
Auto-Darkening Welding Helmets comes ready for use. The only thing

you need to do before your welding is to adjust the position of the

headband and select the correct shade number for your application.





• Larger viewing area: 96MM x 62MM
• German made lens
• Automatically changes filter screen from clear to

dark in 1/20,000 second
• Variable shade adjustment - 9-13 DIN
• UV/IR Protection: Up To DIN 16 At All Times
• Great for use with MIG/MAG, TIG & ARC Welding
• Operator can adjust the time the filter returns from dark to clear
• Automatic Power On / Off (no button to push)
• Utilizes high performance solar cells as power supply
• Battery lifetime up to 4000 hours
• Full face and front of neck protection
• Specially designed headband for greater comfort
• Meets EN, DIN, ISO & ANSI Z87.1 standards
• Large size 13.5" Leather Welding Gloves with flannel lining included

10

14

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

1-800-221-9705 FOR INSTRUCTIONS

Important

When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.

Unpacking

• Astro Pneumatic Tool Co. warrants our products to the original user against defective

material or workmanship for a period of 1 year (except where noted on our price

schedule) from the date of 1st use. Astro reserves the right to determine whether the

product failed because of defective material, workmanship or other causes and to charge

back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products

covered under this warranty free of charge. The distributor should direct the original user

to return the product (with the exceptions listed below) with the distributor’s name,

address, adequate proof of date of purchase or a copy of warranty card, and a short note

explaining the problem.

Failures caused by accident, alteration, or misuse are not

covered by this warranty.

• If one part of this product fails, please do not return the entire product. Astro will

replace free of charge component parts of this product that fail within 1 year of first

use by the original user. Items included in this category include but are not limited

to kits, hand tool kits and any other product where there are multiple items or

components that make up the unit. Please contact the phone number below in

order to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all

warranty repairs. Any repair to the product by unauthorized service representatives

voids this warranty. The rights under this warranty are limited to the original user and may

not be transferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed or implied, including warranties

of merchantability and fitness for a particular purpose. Some states do not allow the

exclusion of limitations of incidental or consequential damages so the

above limitations may not apply to you.

1 YEAR LIMITED WARRANTY

MADE IN CHINA

8077SE

8077SE

8077SE

LARGE VIEWING AREA DELUXE AUTO-DARKENING

SOLAR WELDING HELMET AND WELDING GLOVES

LARGE VIEWING AREA DELUXE AUTO-DARKENING

SOLAR WELDING HELMET AND WELDING GLOVES

LARGE VIEWING AREA DELUXE AUTO-DARKENING

SOLAR WELDING HELMET AND WELDING GLOVES

LARGE VIEWING AREA DELUXE AUTO-DARKENING

SOLAR WELDING HELMET AND WELDING GLOVES

Table of contents