Extron Electronics SW DVI A Series User Guide - Manual (Page 21)

SW DVI A Series • SIS Configuration and Control
SIS Configuration and Control, cont’d
4-4 SW DVI A Series • SIS Configuration and Control 4-5
Command
ASCII Command (host to unit)
Response (unit to host)
Additional description
Input selection Select video and audio input
X!
!
In
X!
All
]
Select both audio and video inputs
X!
.
Select video input only
X!
&
In
X!
V
id
]
Select video input
X!
.
Select audio input only
X!
$
In
X!
Aud
]
Select audio input
X!
.
Input video signal sensing Request status of all inputs
0LS
Sig
X@
•
X@
•
X@
•
X@
]
X@
= input signal status:
1 = pr
esent; 0 = not pr
esent.
N
This command is case-sensitive.
Request status of an individual input
X!
LS
X@
]
N
This command is case-sensitive.
V
ideo muting
V
ideo mute
X@
B
Vmt
X@
]
Mute the video signal.
Read video mute
B
X@
]
Show video muting status
X@
:
1 = muted, 0 = unmuted.
Audio muting Audio mute
X@
Z
Amt
X@
]
Mute the audio signal.
Read audio mute
Z
X@
]
Show audio muting status
X@
:
1 = muted, 0 = unmuted.
Fr
ont panel lockout
Enable/disable executive mode
X@
X
Exe
X@
]
For
X@
: 1 = fr
ont panel locked;
0 = fr
ont panel unlocked (default).
Lockout status
X
X@
]
Show executive mode on/of
f status.
Command/r
esponse table for SIS commands
Command
ASCII Command (host to unit)
Response (unit to host)
Additional description
IR r
eceiver disable fr
om fr
ont panel
Enable/disable IR r
eceiver
X@
* 65#
IRDisable
X@
]
Disable the IR r
emote r
eceiver on the fr
ont panel
fr
om r
eceiving signals fr
om the IR r
emote contr
ol.
IR status
65#
X@
]
V
iew IR r
eceiver status. For
X@
, 0 = of
f, 1 = on.
Firmwar
e version, part number
, and information r
equests
Request information
I
V
X!
•
A
X!
• Vmt
X@
•
Amt
X@
]
Show the selected video and audio input numbers, and the video and audio muting status.
Request part number
N
60-840-xx
]
Show switcher part number
.
SW2 = 60-840-01, SW4 = 60-840-02.
Query firmwar
e version
Q
X#
]
Show firmwar
e build number
X#
, expr
essed to the
second decimal place.
Example:
Q
1.01
]
Query EQ DIP
switch status
41S
Dip
X@
•
X@
•
X@
•
X@
]
X@
= DIP
switch status for each input.
1 = on (up); 0 = of
f (down).
N
This command is case-sensitive.
Query autoswitch mode
72#
Asw
X@
]
Show on/of
f status of autoswitching.
For
X@
: 0 = disabled, 1 = enabled.
Reset Reset
E
ZXXX
}
Zpx
]
Reset the switcher to factory default values.
Upload firmwar
e
Upload firmwar
e
E
Upload
}
...go Upl
]
Upl appears after upload is complete.
Command/r
esponse table for SIS commands (continued)