Quick start guide – B&B Electronics ZXT9-IO-222R2 - Quick Start Guide User Manual
Page 4
pn 8590R1-ZXTx-IO-x-2011QSG –Peer-to-Peer Mode
P
P
e
e
e
e
r
r
-
-
t
t
o
o
-
-
P
P
e
e
e
e
r
r
M
M
o
o
d
d
e
e
C
C
h
h
e
e
c
c
k
k
f
f
o
o
r
r
A
A
l
l
l
l
R
R
e
e
q
q
u
u
i
i
r
r
e
e
d
d
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
Two Zlinx Xtreme I/O Modules of same type
o
ZXT24-IO-222R2
(OR)
o
ZXT9-IO-222R2
This Quick Start Guide
CD with Zlinx™ Manager Software and manual
Antenna
Mounting ears and hardware
Additional items required but not included:
o
10 – 30 VDC Power Supply
o
USB Cable
Conduit mounting accessories sold separately, model
ZXTMT
o
Cable Gland
o
Conduit Accessories
I
I
n
n
s
s
t
t
a
a
l
l
l
l
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
Mount the Zlinx Xtreme I/O modules
Attach antennas to the RPSMA connectors
Attach Conduit hubs, cable glands, etc. as necessary.
Plug the unused hole, if any, using the Membrane Gland.
Accessories kit ZXTMT sold separately.
C
C
o
o
n
n
n
n
e
e
c
c
t
t
F
F
i
i
e
e
l
l
d
d
W
W
i
i
r
r
i
i
n
n
g
g
See Section 11 – “UL Class 1 Div 2 Requirements” for
wiring instructions.
Power Supply Connections:
Connect the10-30 VDC power supply to the PWR IN
+/- terminals on the terminal blocks.
Digital Input Connections:
PWR IN +
DIx
(a) PNP (Sourcing) Input Wiring
with Internal Power Supply
DIx
(b) NPN (Sinking) Input Wiring
with Internal Power Supply
Com
+V
DIx
(c) PNP (Sourcing) Input Wiring with
External Power Supply
Com
Com
DIx
(d) NPN (Sinking) Input Wiring
with External Power Supply
Com
Com
Digital Output (Relay) Connections:
Quick Start Guide
Analog Input & Output Connections:
Zlinx™ Xtreme I/O
3
I
I
n
n
s
s
t
t
a
a
l
l
l
l
Z
Z
l
l
i
i
n
n
x
x
T
T
M
M
M
M
a
a
n
n
a
a
g
g
e
e
r
r
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
Insert the CD into your CD ROM Drive. The Zlinx™
Manager Install Wizard should start. Follow the on-screen
instructions to install the software.
4
If auto run is disabled, locate the ZlinxMgr.exe file on the
CD-ROM drive and double click to launch it. The Install
Wizard should start. Follow the on-screen instructions.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
U
U
S
S
B
B
D
D
r
r
i
i
v
v
e
e
r
r
s
s
Connect the I/O module to the USB port on your PC.
The “Found New Hardware Wizard” will guide you through
the installation process.
When prompted to connect to Windows Updates to search for
drivers, select “No, not at this time” and follow the instructions
for installing from the CD or the location on the hard drive.
Choose the drivers manually from the CD or the location
where Zlinx™ Manager Software is installed.
When the driver is installed a new COM port labeled
“Xtreme” will show up in Windows Device Manager.
E
E
a
a
s
s
y
y
M
M
o
o
d
d
e
e
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
With power applied to the Zlinx Xtreme I/O module, press
and HOLD the Configuration Push Button on the inside
top lid until all the Mode LED's on the front cover flash.
5
6
1
A single LED will flash depending on the current mode
In one I/O module, press the Push Button until the
configuration mode increments to P2P Master mode.
Corresponding LED will be flashing.
If the Push Button is not pressed for 4 sec, the device will
exit with ‘P2P Master’ mode selected.
2
Using similar steps to above, set the other I/O module to
‘P2P Slave’ mode
Refer to Zlinx Xtreme I/O manual for more details