Rainbow Electronics BTD-434 - Manual

Bluetooth Serial Adaptor
User’s Manual
Wireless Solutions in Your Hand
TABLE OF CONTENTS
1. INTRODUCTION…………………………………………………3
1.1. Features………………………………………………………… 3
1.2. Package……………………………….…………...……………3
2. SPECIFICATIONS……………………………………….……...3
2.1. General………………………...……………………………….3
2.2. RS232 Interface………………….........................................4
2.2.1. Pin-out………………………………………………………4
2.2.2. Signals………………………….....................................4
2.3. Factory Settings………………………………………..............4
3. INSTALLATION……………………………………………………4
3.1. Hardware Structure...…………………………………………..4
3.1.1. Reset Button……………………………………………..4
3.1.2. Slide Switch ………………………………………………5
3.1.3. Power Supply …………………………………………….5
3.1.4. LED Status……………………………………………..... 5
3.2 Installation Procedure………………………………………….5
4. USAGE…………………………………………………………….5
4.1 HyperTerminal Settings………………………………………..5
4.2 Configuration…………….……………………………………..5
4.2.1. Configuration Start-up…………………………………..6
4.2.2. Master Role Configuration………………………………6
4.3 AT Command Set………………………………………………6
- 2 -
1. Introduction
Thank you for purchasing our Bluetooth serial adaptor. The adaptor eliminates
your conventional RS232 serial cables, providing an easy-to-use, invisible
connection with superior freedom of movement. This tiny adaptor allows any
device with a standard 9-pin serial port to communicate wirelessly. You can
communicate with another Bluetooth serial adaptor or other Bluetooth-enabled
devices such as a laptop computer, PDA or mobile phone.
1.1. Features
z Supports Bluetooth Serial Port Profile and Generic Access Profile
z No need of external host and software
z Easy of installation and use
z Supports configuration of the local device
z Easy of maintenance
z Supports up to 100 meters (line of sight)
1.2. Package
z Bluetooth serial adaptor: 2 ea
z Antenna: 2 ea
z DB9 male to female converter: 2 ea
z USB cable for power supply: 2 ea
z DC adaptor: 2 ea
z User’s manual: 1
2. Specifications
2.1. General
Specification Description
Baud Rate
Supports 4.8/9.6/19.2/38.4/57.6/115.2/230.4/460.8 Kbps
Coverage Up to 100 m
Connection Point-to-point (pico net)
Signal TxD, RxD, GND, CTS, and RTS
RS-232
Interface
D_SUB 9-pin female
Standard Bluetooth specification version 2.0+EDR
Frequency 2.400 to 2.4835 GHz
Hopping 1,600/sec, 1MHz channel space
Modulation GFSK-1 Mbps, DQPSK-2 Mbps, and 8-DPSK-3 Mbps
Tx. Power Max. 18 dBm (Class 1)
Rx. Sensitivity -86 dBm typical
Antenna Chip antenna or SMA female + external antenna (optional)
Antenna Gain Chip antenna max. 1 to 2 dBi
Power Supply +5 to +9 V DC
Current
Consumption
Max. 90 mA
Operation
Temperature
-20°C to +75°C
Dimensions 35 mm (W) x 65 mm (D) x 16 mm (H)
- 3 -
2.2. RS232 Interface
2.2.1. Pin-out
2.2.2. Signals
Pin Signal Direction Description
2 TxD Output Transmitted data
3 RxD Input Received data
5 GND N/A Signal ground
7 CTS Input Clear to send (Remarks)
8 RTS Output Request to send (Remarks)
9 Vcc Input Power supply
Remarks: The default hardware configuration is for using CTS/RTS. If you want to
use DSR/DTR, please contact us.
2.3. Factory Settings
The factory settings of COM port are as follows:
z Baud rate: 19200 bps
z Data bit: 8
z Parity:
none
z Stop bit: 1
z Flow control: H/W or none
z Others: Please refer to section 4.3 AT Command Set.
3. Installation
3.1. Hardware Structure
The figure below is an outline of the adaptor.
1 Power LED 2 Data LED 3 Link LED 4 RS232 connector
5 Slide switch 6 Mini USB connector 7 Reset button 8 Antenna connector
3.1.1. Reset Button
By pressing the Reset button, you can:
z
Disconnect and reconnect a wireless connection (after a short press) .
z Restore the factory settings (after over three seconds' press).
- 4 -