Rainbow Electronics MAX8742 - Manual (Page 6)

MAX8741/
M
AX8742
500kHz Multi-Output Power-Supply Controllers
with High Impedance in Shutdown
6 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, both PWMs on, SYNC = V L , V L load = 0, REF load = 0, SKIP = 0, T A = -40°C to +85°C , unless otherwise noted.) (Note 6)
PARAMETER CONDITIONS MIN TYP MAX UNITS
V+ Standby Supply Current
V+ = 5.5V to 30V, both SMPSs off, includes
current into SHDN
60 µA
V+ Standby Supply Current in Dropout
V+ = 4.2V to 5.5V, both SMPSs off, includes
current into SHDN
200 µA
V+ Shutdown Supply Current V+ = 4.0V to 30V, SHDN = 0 10 µA
MAX8742 4
Quiescent Power Consumption
Both SMPSs enabled,
FB3 = FB5 = 0,
CSL3 = CSH3 = 3.5V,
CSL5 = CSH5 = 5.3V
MAX8741 4
mW
FAULT DETECTION
Overvoltage Trip Threshold With respect to unloaded output voltage 4 10 %
Output Undervoltage Threshold With respect to unloaded output voltage 60 80 %
Output Undervoltage-Lockout Time
From each SMPS enabled, with respect to
f
OSC
3300 4700 Clks
RESET
RESET Trip Threshold
With respect to unloaded output voltage,
falling edge; typical hysteresis = 1%
-7 -4 %
RESET Delay Time With respect to f OSC 27,000 37,000 Clks
INPUTS AND OUTPUTS
Feedback-Input Leakage Current FB3, FB5; SECFB = 2.6V 50 nA
Logic Input-Low Voltage
RUN/ON3, SKIP, TIME/ON5 (SEQ = REF),
SHDN, STEER, SYNC
0.6 V
Logic Input-High Voltage
RUN/ON3, SKIP, TIME/ON5 (SEQ = REF),
SHDN, STEER, SYNC
2.4 V
Logic Output-Low Voltage RESET, I
SINK = 4mA 0.4 V
Logic Output-High Current RESET = 3.5V 1 mA
TIME/ON5 Input Trip Level SEQ = 0 or V L 2.4 2.6 V
TIME/ON5 Source Current TIME/ON5 = 0, SEQ = 0 or V L 2.5 3.5 µA
TIME/ON5 On-Resistance TIME/ON5; RUN/ON3 = 0, SEQ = 0 or V L 80
Ω
SSOP package 7
Gate-Driver On-Resistance High or low (Note 5)
QFN package 8
Ω
Note 1: Each of the four digital soft-start levels is tested for functionality; the steps are typically in 20mV increments.
Note 2: High duty-factor operation supports low input-to-output differential voltages, and is achieved at a lowered operating frequency
(see the Dropout Operation section).
Note 3: Off mode for the MAX8742 12V linear regulator occurs when the SMPS that has flyback feedback (V DD ) steered to it is disabled.
In situations where the main outputs are being held up by external keep-alive supplies, turning off the 12OUT regulator prevents
a leakage path from the output-referred flyback winding, through the rectifier, and into V
DD .
Note 4: Since the reference uses V
L
as its supply, the reference’s V+ line-regulation error is insignificant.
Note 5: Production testing limitations due to package handling require relaxed maximum on-resistance specifications for the thin
QFN package. The SSOP and thin QFN packages contain the same die, and the thin QFN package imposes no additional
resistance in circuit.
Note 6: Specifications from 0°C to -40°C are guaranteed by design, not production tested.