Milton CAT 938H - Manual (Page 17)

17 938H Wheel Loader specifications
2.30 2.30 2.10 2.50 2.50 2.30
3.00 3.00 2.75 3.25 3.25 3.00
1.97 1.97 1.87 2.11 2.11 2.01
2.58 2.58 2.45 2.76 2.76 2.63
2700 2777 2777 2700 2777 2777
8'10" 9'1" 9'1" 8'10" 9'1" 9'1"
2890 2786 2786 2849 2744 2744
9'5" 9'1" 9'1" 9'4" 9'0" 9'0"
993 1098 1098 1019 1123 1123
3'3" 3'7" 3'7" 3'4" 3'8" 3'8"
2189 2336 2336 2239 2386 2386
7'2" 7'7" 7'7" 7'4" 7'9" 7'9"
50 50 25 50 50 25
1.9 1.9 0.9 1.9 1.9 0.9
7193 7351 7351 7243 7401 7401
23'7" 24'1" 24'1" 23'9" 24'3" 24'3"
5140 5140 5140 5188 5188 5188
16'10" 16'10" 16'10" 17'0" 17'0" 17'0"
11 946 12 105 12 105 11 971 12 131 12 131
39'2" 39'8" 39'8" 39'3" 39'9" 39'9"
11 834 11 737 11 959 11 755 11 658 11 878
26,081 25,867 26,357 25,909 25,694 26,179
10 302 10 205 10 415 10 229 10 131 10 339
22,706 22,492 22,954 22,544 22,329 22,787
141.9 141.1 152.7 134.9 134.2 144.7
31,877 31,703 34,297 30,317 30,143 32,508
14 952 15 027 14 932 14 986 15 061 14 966
32,955 33,120 32,911 33,028 33,194 32,984
1508 1563 1563 1516 1567 1567
4'11" 5'1" 5'1" 4'11" 5'1" 5'1"
2821 2706 2706 2786 2671 2671
9'3" 8'10" 8'10" 9'1" 8'9" 8'9"
51.2 51.2 51.2 50.5 50.5 50.5
Rated capacity
Struck capacity
Width
Dump clearance at full lift and 45 ° discharge
Reach at full lift and 45
° discharge
Reach with lift arms horizontal and bucket level
Digging depth
Overall length
Overall height with bucket at full raise
Loader clearance circle with bucket in carry position
Static tipping load, straight
Static tipping load, articulated at full 40 ° turn
Breakout force
Operating weight
Reach at 2134 mm (7'0") height, 45 ° dumped
Clearance at full raise and dump, on stops
Dump angle at full raise and dump, on stops
m 3
yd 3
m 3
yd 3
mm
ft/in
mm
ft/in
mm
ft/in
mm
ft/in
mm
in
mm
ft/in
mm
ft/in
mm
ft/in
kg
lb
kg
lb
kN
lb
kg
lb
mm
ft/in
mm
ft/in
degrees
Operation Specifications
General Purpose Buckets
Bolt-on
edges
Teeth
and
segments
Teeth
Bolt-on
edges
Teeth
and
segments
Teeth
1400
2,250 2,500 2,750 3,000 3,250 3,500 3,750 4,000 lb/yd 3
yd 3 m 3
kg/m 3
3.00
3.25
3.65
4.00
2.3
2.5
2.8
3.0
1600 1800 2000 2200 2400
Pin-On Bucket Selection Guide
Material Density
% = Bucket Fill Factor
115% 100% 95%
3.65
GP
GP
GP
GP
MH 2.8