Spicer Tandem Drive Axles Service Manual D170, D190, and D590 Series User Manual
Page 25
21
Power Divider
12. Assemble the sliding clutch, shift fork and fork
spring to the input shaft and install assembly into
carrier. Make sure that the shift fork rod is piloted in
the carrier bore.
Before installing input cover, inspect and thoroughly clean
mating surfaces using an appropriate solvent and clean
rag.
Note: Completely remove all old gasket material prior to
applying new Loctite.
13. Apply a bead of Loctite 518 to the carrier surface as
shown in the illustration.
14. Install input cover and capscrews. Torque to the
proper specifications. See the Torque Chart on page
D-1. Tighten fasteners in a criss cross pattern.
15. Install input shaft bearing adjuster, adjust inward
until snug against the bearing cone.
Input Shaft Endplay
16. Back off input bearing cage one notch and check
endplay. Endplay should be between 0.001" to 0.005"
(0.03 to 0.13 mm). Rotate cage in or out to get
proper setting.
IMPORTANT
190 Cover
170 Cover
1 - One Notch
1
Power Divider
- DSP40 Tandem Axle - Dare to Compare (2 pages)
- Ratio Flex Program Guide (46 pages)
- Italcardano Wing In A Box Product Line (3 pages)
- Vibration Diagnostics (1 page)
- Carrier-To-Housing Joint Leak (6 pages)
- Front Axle Shafts for the Jeep JK (2 pages)
- S400 Helical Gear Retrofit Kit Installation (2 pages)
- Electric Shift Unit (1 page)
- Approved Lubricant (16 pages)
- Tandem Drive Axles Pro-40 Single Reduction and Single Reduction with Differential Lock (102 pages)
- Kingpin Bushing and Seal Installation Instructions (2 pages)
- ROUND BEARING DRIVESHAFT COMPONENTS (11 pages)
- NEW REDESIGNED 40K TANDEM CARRIERS (6 pages)
- HAXL-PNI-34 (1 page)
- Tandem Drive Axles Service Manual S400 (34 pages)
- HAXL-PNI-31 (1 page)
- Single Drive Axles Service Manual: S170, S190, S590 (76 pages)
- PDU Cover & Outer Pinion Support Bearing for 46,000 LB (2 pages)
- 2007 Spicer Driveshafts Service Manual (32 pages)
- DRIVELINE COMPONENTS CATALOG SLIP YOKE ASSEMBLIES (28 pages)
- DualRange Tandem Axles (8 pages)
- S400 Redesigned Power Divider Parts for Service (2 pages)
- Wing Bearing Products U-Joint Identification Chart (1 page)
- 10 Series Driveshafts (86 pages)
- Driveline Components Catalog - Companion Flanges (24 pages)
- Gear & Pinion and Wheel Diff Case Kits Released for D_R170, D_R190 Models (3 pages)
- DST40-(P) (3 pages)
- 22719X, MODEL 44 POWER LOCK DISC AND PLATE KIT (1 page)
- 126155 (1 page)
- 2011 Spicer Bulletin 3; SERVICE_TECHNICAL INFORMATION (1 page)
- Drive Axles Service Manual Single Axles 2-Speed & Double Reduction (34 pages)
- X510-5DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS (2 pages)
- Dana “I” Series (2 pages)
- Elimination of PDU Fill Plug On Tandem Drive Axles (2 pages)
- V Drive Components (1 page)
- RST41 (1 page)
- Torsionally Tuned-40 Tandem Drive Axles (2 pages)
- Drive Axles Illustrated Parts List DSS40, DDS40, RSS40, and RDS40 (28 pages)
- Single Drive Axles Service Manual: S140 Series (44 pages)
- DRIVELINE COMPONENTS CATALOG COUPLING SHAFTS - SPL and 10 Series (16 pages)
- Thick Flange Design Carriers (2 pages)
- 2002 Spicer Bulletin; SERVICE_TECHNICAL INFORMATION (1 page)
- Pre-applied Thread Adhesive Compound on Yoke End Nuts (6 pages)
- U-Tube Breather Assembly (2 pages)
- 130542 (1 page)