Spicer Tandem Drive Axles Service Manual D170, D190, and D590 Series User Manual
Page 18
14
Power Divider
10. Remove the thrust washer and helical side gear.
11. Remove the inter-axle differential assembly.
12. Remove the output side gear and pump assembly.
13. To replace the input bearing cup, back off the
bearing cage locking fastener or jam nut and stud.
14. Input cage is threaded in to the PDU cover, use the
proper tool to remove the cage from the cover.
15. Use a suitable bearing puller to replace the input
bearing cup.
Note: In August of 2006 the piloted input adjuster design was
implemented. The lockin and fastener was replaced with
a 12mm stud and jam nut. It is not recommended that
the piloted designed adjuster and cover be mixed with
the non-piloted design.
Cover Pilot
Adjuster Pilot
See also other documents in the category Spicer For the car:
- DSP40 Tandem Axle - Dare to Compare (2 pages)
- Ratio Flex Program Guide (46 pages)
- Italcardano Wing In A Box Product Line (3 pages)
- Vibration Diagnostics (1 page)
- Carrier-To-Housing Joint Leak (6 pages)
- Front Axle Shafts for the Jeep JK (2 pages)
- S400 Helical Gear Retrofit Kit Installation (2 pages)
- Electric Shift Unit (1 page)
- Approved Lubricant (16 pages)
- Tandem Drive Axles Pro-40 Single Reduction and Single Reduction with Differential Lock (102 pages)
- Kingpin Bushing and Seal Installation Instructions (2 pages)
- ROUND BEARING DRIVESHAFT COMPONENTS (11 pages)
- NEW REDESIGNED 40K TANDEM CARRIERS (6 pages)
- HAXL-PNI-34 (1 page)
- Tandem Drive Axles Service Manual S400 (34 pages)
- HAXL-PNI-31 (1 page)
- Single Drive Axles Service Manual: S170, S190, S590 (76 pages)
- PDU Cover & Outer Pinion Support Bearing for 46,000 LB (2 pages)
- 2007 Spicer Driveshafts Service Manual (32 pages)
- DRIVELINE COMPONENTS CATALOG SLIP YOKE ASSEMBLIES (28 pages)
- DualRange Tandem Axles (8 pages)
- S400 Redesigned Power Divider Parts for Service (2 pages)
- Wing Bearing Products U-Joint Identification Chart (1 page)
- 10 Series Driveshafts (86 pages)
- Driveline Components Catalog - Companion Flanges (24 pages)
- Gear & Pinion and Wheel Diff Case Kits Released for D_R170, D_R190 Models (3 pages)
- DST40-(P) (3 pages)
- 22719X, MODEL 44 POWER LOCK DISC AND PLATE KIT (1 page)
- 126155 (1 page)
- 2011 Spicer Bulletin 3; SERVICE_TECHNICAL INFORMATION (1 page)
- Drive Axles Service Manual Single Axles 2-Speed & Double Reduction (34 pages)
- X510-5DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS (2 pages)
- Dana “I” Series (2 pages)
- Elimination of PDU Fill Plug On Tandem Drive Axles (2 pages)
- V Drive Components (1 page)
- RST41 (1 page)
- Torsionally Tuned-40 Tandem Drive Axles (2 pages)
- Drive Axles Illustrated Parts List DSS40, DDS40, RSS40, and RDS40 (28 pages)
- Single Drive Axles Service Manual: S140 Series (44 pages)
- DRIVELINE COMPONENTS CATALOG COUPLING SHAFTS - SPL and 10 Series (16 pages)
- Thick Flange Design Carriers (2 pages)
- 2002 Spicer Bulletin; SERVICE_TECHNICAL INFORMATION (1 page)
- Pre-applied Thread Adhesive Compound on Yoke End Nuts (6 pages)
- U-Tube Breather Assembly (2 pages)
- 130542 (1 page)