Appendices 3m™ super close projection system – 3M SCP717 User Manual
Page 55
50
© 3M 2008. All Rights Reserved.
Appendices
3M™ Super Close Projection System
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SEND from projector automatically
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
when got invalid command
NG
when standby/warming/cooling/out of range
INFOn
n : 0/1/2/3 = standby / warm-up / cooling / out range
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
READ from projector
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 Code
Function
Projector Return
Description
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
IR098
Information
OKabbbbcddddef
bbbb : LampHour
c : source 0/1/2/3/4/5= none/dvi/vga1/vga2/s-video/video
dddd : FW version
e : display mode
f : status 0/1/2/3 = standby/warm-up/cooling/out range
IR099
Info. to web only
OK[data]
( !!! Caution !!! data[ ] are all ASIC character.)
data[0] :
Power
1/0=on/off
data[1] :
Lamp lit
1/0=ok/failed.
data[2] :
Eco Mode
1/0=on/off
data[3] :
Freeze
1/0=on/off
data[4] :
Source Lock
1/0=on/off
data[5] :
Mute
1/0=on/off
data[6] :
Information
1/0=on/off
data[7] :
Blank
1/0=on/off
data[8] :
High Altitude
1/0=on/off
data[9] :
Keypad Lock
1/0=on/off
data[10] :
-none-
0
data[11] :
Signal Power On
1/0=on/off
data[12] :
Direct Power On
1/0=on/off
data[13] :
Eco Standby
1/0=on/off
data[14] :
Source
0/1/2/3/4/5/6= None/DVI/VGA1/VGA2/S-Video/Video
data[15] :
Display format
0/1/2/3/4/5=Auto/4:3/16:9/Full/window/LetterBox
data[16] :
Display mode
0/1/2/3/4/5= PC/Photo/Video/Cinema/sRGB/User
data[17] :
Colour temperature 0/1/2/=low/med/high
data[18] :
Gamma
0/1/2/3
data[19] :
-none-
0
data[20] :
Logo
0/1=3M/User
data[21] :
Mounting
1/0=on/off
data[22] :
Rear
1/0=on/off
data[23..24] : Projector ID
XX
data[25..26] : Volume
XX
data[27..28] : Sharpness
XX
data[29..30] : Phase
XX
data[31..32] : White Intensity
XX
data[33..34] : Zoom
XX
data[35..37] : Brightness
XXX
data[38..40] : Contrast
XXX
data[41..43] : V Image Position
XXX
data[44..46] : Ver. keystone
XXX
data[47..49] : Auto Power Off
XXX
data[50..52] : Sleep Timer
XXX
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Projector SEND to lan module
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 Code
Function
Lan module Return
Description
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
IR110n
alarm inform
n : 0/1/2/3/4/5: Normal/Thermal Switch Error/Fan Lock/Over Temperature/Lamp Hours Running Out/Lamp Fail
IR04901?
Query lan module
IR25901n
n : n=AAAAAAAANNNNNNNNGGGGGGGGDDDDDDDDPC
A: IP Address
N: Subnet Mask
G: Gateway
D: DNS
P: DHCP Mode(0/1: Off/ON)
C: RJ-45 Connector State(0/1: Disconnect/Connect)
IR23904n
Set lan module
IDooIR03904
n : n=AAAAAAAANNNNNNNNGGGGGGGGDDDDDDDD
A: IP Address
N: Subnet Mask
G: Gateway
D: DNS
IR04905n
Set lan module
IDooIR03905
n : 1/0=DHCP on/off
IR03903
Reset lan module