Tyco 4100U-S1 User Manual

Tyco Safety

Fire

Australian
Installation
Manual

4100U-S1 Fire Indicator Panel
Installation & Maintenance

Australian
Installation &
Maintenance
Manual

LT0394

Table of contents

Document Outline

Copyrights and Trademarks
Approvals
Manufacture
Product / Site
Non-Disclosure Agreement
End User Liability Disclaimer
Model Number & Firmware Revision
Document
Amendment Log
Cautions, Warnings, and Regulatory Information
Table of Contents
List of Figures
List of Tables
Chapter 1 Introduction to the 4100U-S1 Fire Alarm System
- Introduction
  - In this Chapter
- Basic Configuration
  - Overview
  - System Design
- 4100U-S1 Part Codes
- 4100 Part Codes (Non-4100U)
Chapter 2 Installing 4100U-S1 Components
- Introduction
  - In this Chapter
- Introduction to 4100U-S1 Cabinet
- Step 1. Mounting Cabinets
  - Overview
- Step 2. Mounting Card Bays to Cabinets
  - Overview
- Step 3. Configuring Cards
- Step 4. Interconnecting Modules and Bays
- Step 5. Installing Modules into Expansion Bays
- Step 6. Installing LED/Switch Modules into Expansion Bays
- 4100U Fan Control Module
Chapter 3 Networking
- Introduction
  - In this Chapter
- Network Configuration
- Getting Started
  - Overview
- Introduction to the 4100 Network Interface Card (NIC)
- Step 1. Configuring Network Cards
- Step 2. Mounting Media Cards to the NIC
  - Overview
  - Media Card Mounting
- Step 3. Mounting Network Cards in the 4100U-S1
- Step 4. Wiring Network Cards
Chapter 4 The System Power Supply & Alarm Relay Card
- Introduction
  - In this Chapter
- SPS Specifications
  - Input/Output/BatterySpecifications
  - SPS Current Consumption
- SPS Adjustments
  - Adjusting Voltages
  - Setting Jumpers and DIP Switches
- SPS LED Indications
  - Status LEDs
- Troubleshooting an SPS
- The Alarm Relay Card
- Brigade Interfaces
Chapter 5 SPS Field Wiring (4100U-S1)
- Introduction
  - In this Chapter
- General Field Wiring Guidelines
  - General Guidelines
- SPS NAC Field Wiring Guidelines
- Power Supply Wiring Distances
- Using T-Gen 50 with 4100U-S1
- SPS Auxiliary Power Wiring
- SPS Relay Wiring
- SPS IDNet Wiring
Chapter 6 Installing a 4100U IDNet Card
- Introduction
  - In this Chapter
- The IDNet Card
- Installing the IDNet Card onto the PDI
  - Overview
- Configuring the Card
- Wiring to IDNet Devices
- Troubleshooting on IDNet
Chapter 7 PC Software Connections
- Introduction
  - In this Chapter
- Software Modes
  - Overview
  - Software Modes
Chapter 8 Installation Checklist, Commissioning & Maintenance
- Introduction
  - In this Chapter
- Alignment & Adjustment
  - Overview
- Power Up & Placing into Operation
- Maintenance
Appendix A Card Address DIP Switch
- Overview
Appendix B Programming Requirements
- Introduction
  - Required Features
  - Notes
Appendix C Checking System Wiring
- Overview
  - Using the Volt/ Ohm Meter
  - Meter Readings
Appendix D Earth Fault Detection
- Overview
- General Guidelines
- Earth Fault Searching from the Front Panel
- Search Results
Appendix E Related Documentation
Appendix F Compatible Actuating Devices
- Introduction
  - In this Chapter
- List of Approved Devices
- Compatible Detectors, IDNET
- Compatible Addressable Field Devices, IDNet
Appendix G 4100U-S1 Specifications
- General
  - Fuses
  - Firmware Features
- Voltage & Current Ratings of Modules & Assemblies
Appendix H Power Supply & Battery Capacity Calculations
- Power Supply
  - Battery Capacity
Appendix I List of Drawings