Toshiba RAV-SM1100UT-E - Manual (Page 52)

49
PRECA
UTIONS FOR SAFETY
W
ARNING
W
ARNINGS ABOUT INST
ALLA
TION
•
Mak
e sure to ask the qualified installation prof
essional in
electr
ic wor
k
to install the remote controller
.
If the remote controller is inappropr
iate installed b
y
y
ourself
, it ma
y cause
, electr
ic shoc
k, fire
, and so on.
W
ARNINGS ABOUT OPERA
TION
•
When y
ou are a
w
are of something abnor
mal with the air
conditioner (smells lik
e something etc.), immediately tur
n
off the main po
wer supply s
witch or circuit break
er
, from
the mains to stop the air conditioner
, and mak
e contact
with the dealer
. If the air conditioner is contin
uously
oper
ated with something abnor
mal, it ma
y cause machine
failure
, electr
ic shoc
k, fire
, and so on.
W
ARNINGS ABOUT MO
VEMENT AND REP
AIR
•
Do not repair an
y unit b
y
y
ourself
.
•
Whene
v
er the air conditioner needs repair
, mak
e sure to
ask the dealer to do it.
If it is repaired imperf
ectly
, it ma
y
cause electr
ic shoc
k or fire
.
CA
UTION
CA
UTIONS ABOUT OPERA
TION
•
Carefully read this man
ual bef
ore star
ting the air condi-
tioner
.
There are man
y impor
tant things f
or the saf
ety and
the correct usage
.
•
Do not touch an
y s
witches with wet finger
, otherwise y
o
u
ma
y get an electr
ic shoc
k.
•
When the air conditioner w
as not be used f
or a consider-
ab
ly long time
, tur
n off the main s
witch or the circuit
break
er
, f
or saf
ety
. Disconnect from the po
wer supply
pre
v
ents the unit from lightning and po
w
er supply surge
.
•
Pre
v
ent an
y liquid from f
alling into the remote controller
.
Do not spill juice
, water or an
y kind of liquid.
NAME AND OPERA
TION
Remote Contr
oller
•
Max.
8 indoor units can be oper
ated b
y
a remote controller as a g
roup
.
1
T
ransmitting par
t
2
Remote contr
oller sensor
The per
ipher
al temper
ature is sensed when
the sensor b
utton is pushed to remote
controller side
.
3
Mode displa
y section
The operation mode is displa
y
ed.
4
Star
t/Stop b
utton
Pushing this b
utton star
ts
, and pushing
again stops the unit.
5
Mode Select b
utton
Pushing this b
utton selects an oper
ation
mode.
6
Air v
olume b
utton
7
Time Setup
b
utton
This b
utton is used when the timer is
setup
.
8
Reset b
utton
This b
utton is used after replacement of
batter
y or selection of slide s
witch.
9
Slide switc
h
10
P
a
rt
storing batteries
11
Co
ver
Slide the co
v
er holding its both sides
.
12
A
U
T
O
flap displa
y diff
er
s accor
ding
to the installed unit.
13
Setup T
emp.
b
utton
Ev
e
ry pushing this b
utton, temperature
rises b
y
1˚C
.
Ev
e
ry pushing this b
utton, temperature
lo
wers b
y
1˚C
.
14
Filter b
utton
The remote controller is not oper
ated
e
v
en if this s
witch is pushed.
15
Swing/Air direction b
utton
16
Address b
utton
17
V
entilation b
utton
The remote controller is not oper
ated
e
v
en if this s
witch is pushed.
18
Sensor b
utton
This b
utton is used when selecting the
temp
. sensor at the remote controller
side
. At the shipment from the f
actor
y,
this b
utton is set to the temp
. sensor at
the indoor unit.
SET
ACL
SE
NS
OR
CL
SK
N
AH
C ADR
ADR
1
2
4 6 8
5 7 9 10 11
14
3
16
13
12
15 17
18
ACCESSORIES