Mosquito nr, Om nr, En-80 – Onkyo AV Receiver TX-NR5010 User Manual
Page 80
Advanced Operations
En-80
■
Saturation
`
–50 to 0 to +50
With this setting, you can adjust saturation. “–50” is the
weakest color. “+50” is the strongest color.
■
Color Temperature
`
Warm
`
Normal
`
Cool
With this setting, you can adjust the color temperature.
■
Gamma
`
–3 to 0 to +3
With this setting, you can adjust the incoming picture’s R
(red), G (green), and B (blue) color signal in relation to the
output color signal.
■
Red Brightness
`
–50 to 0 to +50
With this setting you can adjust the brightness of red color.
“–50” is the darkest. “+50” is the brightest.
■
Red Contrast
`
–50 to 0 to +50
With this setting you can adjust the contrast of red color.
“–50” is the least. “+50” is the greatest.
■
Green Brightness
`
–50 to 0 to +50
With this setting you can adjust the brightness of green
color. “–50” is the darkest. “+50” is the brightest.
■
`
–50 to 0 to +50
With this setting you can adjust the contrast of green color.
“–50” is the least. “+50” is the greatest.
■
Blue Brightness
`
–50 to 0 to +50
With this setting you can adjust the brightness of blue
color. “–50” is the darkest. “+50” is the brightest.
■
Blue Contrast
`
–50 to 0 to +50
With this setting you can adjust the contrast of blue color.
“–50” is the least. “+50” is the greatest.
Note
• “Picture Adjust”
cannot be used when:
– The NET input selector is selected, or
– “Monitor Out” is set to “Sub” (
).
• “Picture Adjust” can be used when the USB input selector is
selected; however, only when iPod/iPhone is connected and
Standard Mode or Extended Mode (Video) is selected.
*1
This procedure can also be performed on the remote controller
by using the Quick Setup (
*2
When a 3D video source is input, “Wide Mode” is fixed to
“Full”.
*3
When “Metadata Compatible” is enabled (
“Picture Mode” is fixed to “Direct”.
*4
When the “Picture Mode” setting is set to anything other than
“Custom”, this setting cannot be used.
*5
If the “Resolution” setting is set to “4K Upscaling”
(
), this setting is fixed at “Off”.
*6
Press CLR if you want to reset to the default value.
*7
When the “Noise Reduction” setting is set to anything other
than “Off”, this setting cannot be selected.
*8
With some TVs, there may be no picture when this setting is
set to “4K Upscaling”.
*9
When “Resolution” is set to “1080p/24” or “4K Upscaling”
while “Monitor Out” is set to “Analog”, the video is output in
1080i.
*10
When “Resolution” is set to “Auto” while “Monitor Out” is
set to “Analog”, the video is output as “Through”.
Audio Selector
■
Audio Selector
`
ARC:
The audio signal from your TV tuner can be sent to
HDMI OUT MAIN of the AV receiver.
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`
HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI (HDMI
IN) and digital audio inputs (COAXIAL IN or
OPTICAL IN) have been assigned, HDMI input is
automatically selected as a priority.
`
COAXIAL:
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
`
OPTICAL:
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and HDMI
inputs have been assigned, optical input is
automatically selected as a priority.
`
Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are both
digital and analog inputs.
Note
• This setting can be made only for an input source that is assigned
to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET and USB input
selectors.
• When using the Whole House Mode, this setting cannot be
selected.
• With the GAME2 input selector, “Analog” cannot be used.
*1
You can select “ARC” if you select the TV/CD input selector.
But you cannot if you’ve selected “Off” in the “Audio Return
Channel” setting (