Onkyo AV Receiver TX-NR5010 - Manual (Page 67)

Advanced Operations
En-67
Note
• “Speakers Type(Front A)” and “Speakers Type(Front B)”
cannot be set to “Bi-Amp” or “Digital Crossover” at the same
time.
• Powered Zone 2 cannot be used if “Speakers Type(Front B)” is
enabled.
• Powered Zone 3 is not available in the following cases:
– The “Speakers Type(Front A)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Speakers Type(Front B)” is enabled.
– The “Powered Zone 2” setting is set to “No”.
• When the “Powered Zone 3” setting is set to “Yes”
( ➔ page 66 ) while Powered Zone 2 is enabled ( ➔ page 89 ),
the surround back speakers cannot be used.
• When the “Powered Zone 2” setting is set to “Yes”, the front
wide speakers cannot be used.
• When the “Powered Zone 3” setting is set to “Yes”, the front
high speakers cannot be used.
• “11ch Playback” is not available in the following cases:
– The “Speakers Type(Front A)” setting is set to “Bi-Amp” or
“Digital Crossover”.
– The “Speakers Type(Front B)” is enabled.
– The “Powered Zone 2” setting is set to “Yes”.
– The “Zone 2 HDMI” setting is set to “Use”.
• If the “11ch Playback” setting is set to “Yes”, the audio of front
wide channel is output from FRONT WIDE PRE OUT only.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and levels
of the front speakers A and front speakers B independently.
The other speakers (i.e., subwoofer, center, surround,
surround back and front high) use the same crossover
frequencies, distances, and levels for Speakers A and
Speakers B. Specify “Full Band” for speakers that can
output low frequency bass sounds adequately, for example,
speakers with a good sized woofer. For smaller speakers,
specify a crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
■ Subwoofer
` 1ch:
Audio signal is outputted from SW1 jack only.
` 2ch :
Audio signal is outputted from SW1 and SW2 jacks.
` No
■ Front
(Setting Speakers A and Speakers B)
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
• If any of “Center”, “Surround”, or “Front High” is set to “Full
Band”, the “Front” (Speakers B) setting is fixed to “Full Band”.
■ Center *8 , Surround *8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Front Wide *3*4*6*7*8*9 , Front High *1*2*3*6
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
■ Surround Back *1*5*6*10
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
This setting is set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup function ( ➔ page 42 ). For Speakers B,
you need to change the settings manually.
To be continued