Pioneer BDP-V6000 - Manual (Page 72)

09
72
En
Others
Problem Check Remedy
Playe r cannot be restored to
the facto ry defaults.
Is a disc loaded in the player? Remove the disc from the player before restoring the player to the
facto ry defaults (page 51).
Playe r cannot be controlled
by RS-232C.
Check the Advanced Setup  Baud Rate setting and the serial
inte rface specifications (page 56 and 58).
The player’s power turns off
automatically.
Is Auto Power Off set to
On?
If Auto Power Off is set to On, the player’s power turns off
automatically if no o peration is performed for over 30 minutes
( page 46).
Is Display Power Off set to
On?
The player’s power may turn off together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn off when the TV’s power is turned off, set Display Power
Off to Off (page 44).
The player’s power turns on
automatically.
Is KURO LINK set to On? The player’s power may turn on together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn on when the TV’s power is turned on, set KURO LINK to
Off (page 44).
Playe r cannot be operated
with remote control.
Is an AV receiver or amplifier
connected to the CONTROL
IN terminal on the player’s
rear panel?
O perate with the remote control of the device connected to the
CONTROL IN terminal.
A re you operating the remote
cont rol from a point too far
away f rom the player?
O perate from within 23 feet (7 m) of the remote control sensor.
A re the batteries dead? Re place the batteries (page 7).
Is the RC-232C Key Lock
command set? Cancel the Key Lock command. Fo r details, see the communications
inte rface user's manual.
Black sc reen is displayed
though no o perations are
being performed.
Is Screen Saver set to On? • The sc reensaver turns off when the player’s front panel or remote
cont rol is operated.
• If you do not want the sc reensaver to be activated, set Screen Saver
to Off (page 46).
F ront panel display does not
tu rn on.
Has the f ront panel display
been tu rned off?
P ress FL DIMMER on the remote control to switch the front panel
dis play’s brightness (page 12).
Buttons on the player's front
panel cannot be operated or
the disc t
ray does not open.
Is Front Key Lock set to All
o r Tray?
Set Front Key Lock to Off (page 55).
In put of connected TV and AV
system switches
automatically.
Is KURO LINK set to On? The in put of the TV and AV system (AV receiver or amplifier, etc.)
connected to the HDMI OUT terminal may automatically switch to the
player when playback starts on the player or the menu screen (Home
Media Galle
ry, etc.) is displayed. If you do not want the inputs of the
connected TV and AV system (AV receiver or amplifier, etc.) to switch
automatically, set KURO LINK to Off (page 44).
“P rocessing failed.” is
dis played.
If the message a ppears repeatedly, please ask your nearest Pioneer
autho rized service center or your dealer to carry out repair work.
Settings you have made have
been clea
red.
• Have you disconnected the
power cord while the player’s
power was on?
• Has the re been a power
failu re?
Always press  STANDBY/ON on the player’s front panel or
 STANDBY/ON on the remote control and check that POWER OFF
has tu
rned off from the player’s front panel display before
disconnecting the power cord. Be particularly careful when the power
co rd is connected to the AC outlet on another device because the
player turns off in conjunction with the device.
V6000_CUXJ_EN.book 72 ページ ２００９年６月５日 金曜日 午前１１時５７分